What the zinc acetate COA actually contains
The certificate for a zinc acetate dihydrate lot reports appearance, zinc and acetate identity, assay by complexometric titration at 99.0–101.0%, elemental zinc at 29.0–32.0%, water by Karl Fischer at 10.0–14.0%, the heavy-metal panel, microbiology and an 80 mesh particle size. The limits below are the catalog specification; the batch COA is the document that confirms a particular pouch or drum.
The assay, the zinc figure and the water line are three views of the same dihydrate; the certificate is only readable when each one carries its basis and its method.
The certificate as a test report
A certificate is auditable when every row carries what was measured, the method that produced the number, and the limit the lot was released against. A row that says only “conforms” gives a verdict without evidence. On this salt the identity row has to show both ions, because a zinc figure alone would also fit zinc sulfate, zinc oxide or a zinc chelate. Water is a Karl Fischer result, not a loss on drying, because the crystal water is part of the molecule.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | White to off-white, free-flowing powder |
| Identification | Zinc reaction, acetate reaction and IR | Conforms to the reference |
| Assay (dried basis) | Complexometric titration | 99.0–101.0% |
| Zinc (Zn) | Complexometric titration (EDTA) | 29.0–32.0% |
| Water | Karl Fischer | 10.0–14.0% |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
| Particle size | Sieve analysis | ≥95% through 80 mesh |
The basis: assay, zinc and water on one mass balance
The formula C4H6O4Zn·2H2O has a molar mass of about 219.50 g/mol. Zinc is 65.38 of that, or 29.8%; two acetate ions are 118.09, or 53.8%; two water molecules are 36.03, or 16.4%. The catalog ranges sit on that balance: zinc 29.0–32.0% and water 10.0–14.0% describe a dihydrate that has lost part of its crystal water. A drier lot carries more zinc per gram; that is a hydration difference, not a stronger product.
The assay basis has to be printed in the row. A 99.0–101.0% figure read as-is cannot sit beside a 12% water result, because the salt and the water would add to more than 100% of the powder. Read on the dried basis, the numbers reconcile: a lot at 12.0% water and 31.0% zinc is about 87% zinc acetate as-is, and the dried-basis titration is close to 100%. The acetate line is the other half of the identity: one zinc ion for every two acetate ions, so the zinc titration and the acetate reaction should agree.
Release limit versus batch result
The release limit is the acceptance boundary; the batch result is what the laboratory measured on that lot. Both belong on the page, in separate columns, with the method beside them. A result column filled with the specification range is not a result.
| Parameter | Release limit | Result column |
|---|---|---|
| Assay | 99.0–101.0% dried basis | A measured percentage, with the basis and the method |
| Zinc | 29.0–32.0% | A measured percentage by EDTA titration |
| Water | 10.0–14.0% | A measured percentage by Karl Fischer |
| Identification | Zinc and acetate conform | The tests performed and the IR reference used |
| Heavy metals | Per element | A measured figure in mg/kg for each element |
| Microbiology | Counts and absence | The count and the absence statement for the lot |
| Particle size | ≥95% through 80 mesh | The measured percentage through the sieve |
One cross-check catches most certificate errors before a sample is opened. Zinc high with water low is a drier hydrate; zinc low with water high is surface moisture or a dilution. A certificate that reports both lines without that check has left the arithmetic to the reader.
What moves between batches
Water is the first variable. Zinc acetate dihydrate is hygroscopic, and it can also lose crystal water in a dry store, so the Karl Fischer result moves in both directions. The assay on the dried basis can stay inside 99.0–101.0% while the as-is zinc figure shifts, which is why the water line belongs on the release certificate and not only on a stability report.
Particle size is the second. The catalog form is an 80 mesh powder; granulation is a separate on-request format. Milling and sieving change flow, dust and dissolution without changing the chemistry. Colour and odour are weaker signals: a yellow or brown tint points to iron, and a sharp acetic odour can indicate free acid or a moisture problem. The lot code on the certificate should match the pouch, the drum and the retained sample.
When to order an outside test
Order an independent test for a new source, a first shipment into a regulated market, a disputed hydrate or salt claim, or an unreconciled result. The useful panel is not a full repeat: EDTA titration for zinc, Karl Fischer for water, an acetate test by ion chromatography or titration, ICP-MS for the metals, microbiology, and FTIR or XRD for the solid form.
Add a sulfate test by ion chromatography when the salt is in question. Zinc sulfate is the nearest substitute and can pass a zinc assay; the sulfate result and the lower solution pH are what separate it from the acetate. Ask the laboratory for its detection limit on each screen, and keep the sample tested as the sample retained.
What to compare between suppliers
Put six lines side by side: form and CAS number; assay result with its basis; zinc and water results; acetate identity and a sulfate result; heavy metals and microbiology; pack size and lot code. Two quotations that agree on assay but differ on water or the acetate test are not describing the same powder. The second layer is traceability: who manufactured the lot, which zinc and acetate sources were used, and which drying and milling steps were applied.
The catalog specification sits on the zinc acetate product page. The tests that separate the dihydrate from other zinc salts are on the identity page; the salt comparison is on the grades page; the methods are in the analytical methods library; the release workflow is on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation