Zinc acetate or another zinc salt: what the grade changes
A zinc label declares the element, but the drum contains a salt, and the salt is most of the mass. Zinc acetate dihydrate carries about 29.8% zinc, 53.8% acetate and 16.4% water at the theoretical formula; zinc sulfate heptahydrate carries about 22.7% zinc; zinc gluconate about 14.3%; zinc citrate dihydrate about 32.1%. The grade question is a salt question first and a mesh or granulation question second.
The salt decides the zinc per gram, the pH in solution and the name on the label before the mesh or the pack matters.
One element, several salts
Zinc acetate dihydrate, C4H6O4Zn·2H2O, has a molar mass of about 219.50 g/mol and a theoretical zinc content of 29.8%. The acetate is a weak-acid anion, so an aqueous solution sits close to neutral rather than strongly acidic. That single property separates the salt from zinc sulfate at the formulation stage, before the assay or the certificate is discussed.
The catalog form is an 80 mesh powder; granulated material is available on request. Mesh and granulation change flow, dust and dissolution, not the zinc figure. The catalog zinc range of 29.0–32.0% and water range of 10.0–14.0% describe a dihydrate that has lost part of its crystal water, so a lot near the top of the zinc range is drier, not stronger. The label names the salt, not only the element, and a change of salt is a change of ingredient.
The options side by side
| Salt or form | Zinc | Water | In water | Fits | Watch |
|---|---|---|---|---|---|
| Zinc acetate dihydrate, 80 mesh | 29.0–32.0% | 10.0–14.0% Karl Fischer | Freely soluble; pH 6–8 at 5% | Capsules, tablets, powder blends, sticks | Hygroscopic; fine powder dusts |
| Zinc acetate, granulated | Same specification | Same specification | Same as the 80 mesh line | Tablets, sachets, blends | Granulation aids must be declared |
| Zinc sulfate heptahydrate | 22.0–23.0% | 43.0–46.0% | Freely soluble; pH 4.4–5.6 at 5% | Capsules, tablets, powder blends | Acidic; about 44 mg per 10 mg zinc |
| Zinc gluconate | 12.5–14.0% | ≤1.0% loss on drying | Freely soluble; near neutral | Clear drinks, syrups, capsules | About 70 mg per 10 mg zinc |
| Zinc citrate dihydrate | 31.0–32.5% dried basis | ≤6.0% loss on drying | Slightly soluble; dispersion | Capsules, tablets, opaque sticks | Suspension settles on standing |
The first two rows are process variants of one salt; the last three are different anions and different specifications. Moving between the acetate block and the sulfate block changes the CAS number, the zinc per gram, the solution pH and the label name.
Solubility, pH, taste and the powder in the room
Zinc acetate dissolves freely and gives a clear, colourless solution. A 5% solution sits at about pH 6–8, close to neutral, and the acetate provides some buffering around that range. The taste is saline and faintly metallic, with a slight acetic note that becomes more noticeable as the concentration rises. None of those descriptions replaces a trial in the real matrix: the sugar system, the acidulant, the flavour and the serving temperature decide what the consumer tastes.
Zinc sulfate is the acidic alternative. A 5% solution sits at about pH 4.4–5.6, and the taste is more astringent at the same zinc concentration. Zinc gluconate is mild and freely soluble, which suits clear drinks; zinc citrate is only slightly soluble and behaves as a dispersion. The acetate sits between the gluconate and the sulfate on mass per milligram of zinc, with a near-neutral solution that is useful in pH-sensitive matrices.
Powder handling is the second physical question. The 80 mesh acetate flows well but dusts and picks up moisture in an open liner; a granulated grade is easier to run on a tablet press and generates less dust. The pack has to be closed after sampling, and the scoop should not stay in the drum.
What the dosage form can carry
The arithmetic is division, and it decides most capsule projects. At 29.8% zinc, a 10 mg claim needs about 33.6 mg of zinc acetate dihydrate; at 22.7%, the same claim needs about 44.0 mg of zinc sulfate heptahydrate. At 50 mg the weights are about 167.8 mg and 219.9 mg. The gluconate needs about 70 mg for 10 mg of zinc, and the citrate about 31 mg. Those are theoretical figures; the certificate's zinc result is the number to use at the balance.
The difference is large enough to change the dosage form. A small capsule that fits 33.6 mg of acetate may not fit 44 mg of sulfate plus the excipients, and a tablet built on the sulfate needs more compression mass for the same claim. A stick pack or a clear drink takes the acetate because it dissolves without a dispersion. A lozenge or a chew can use the acetate's near-neutral solution and mild taste, but the sugar and acid system still has to be tested.
The label follows the salt. A Supplement Facts panel declares “Zinc (as zinc acetate)” and the elemental zinc per serving; the ingredient list names zinc acetate. A panel written for zinc sulfate is not a label for the acetate even when the elemental zinc figure is the same.
How to write the specification
- “Zinc acetate dihydrate, C4H6O4Zn·2H2O, CAS 5970-45-6.”
- “Assay 99.0–101.0% by complexometric titration; state the basis.”
- “Zinc 29.0–32.0%; water 10.0–14.0% by Karl Fischer.”
- “Identification: zinc reaction, acetate reaction and IR against a named reference.”
- “≥95% through 80 mesh; granulated on request; heavy metals and microbiology as catalog.”
- “No substitution with zinc sulfate, zinc oxide or another zinc salt without written change control.”
A specification that says only “zinc” has described neither the salt nor the hydrate. The product hub carries the catalog line; the acetate versus sulfate page works through the pH and label consequences; the COA page shows how the figures are reported.
What changes when you switch, and when not to
A salt switch is a change control, not a substitution. It moves the fill weight, the pH of the matrix, the taste, the stability file and the label, and it needs a new specification, a matrix trial at the real process conditions and a new artwork proof. A capsule qualified on the sulfate cannot be filled with acetate at the same weight: the zinc dose would rise by about 30%.
The switch is justified when the current salt is the constraint: a pH-sensitive matrix that cannot take the sulfate acidity, a capsule that cannot hold the sulfate mass, or a taste trial that favours the acetate. It is not justified by one quotation or a higher zinc figure. If the current salt works, the label is approved and the file is complete, the burden sits on the change.
The zinc sulfate product page presents the acidic salt from its own side; the stability page covers the acetate powder and solution; the analytical methods library explains the zinc titration; the quality page describes the release file.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation