06 Identity & adulteration

How to prove a zinc acetate lot is the dihydrate

Technical document 06 · Reviewed 2026-11-20 · Zinc Acetate

On this page
  1. Identity evidence, layer by layer
  2. The zinc, acetate and water ratio
  3. FTIR and XRD: the solid-state check
  4. What substitution looks like
  5. Identity lines for the specification
  6. Five questions before approval

A zinc acetate lot is the dihydrate when five lines agree: the document names the dihydrate and CAS 5970-45-6; complexometric titration gives 29.0–32.0% zinc; the acetate reaction and IR show the acetate ion; Karl Fischer gives 10.0–14.0% water; and the solid-state pattern matches the dihydrate reference. The assay alone cannot separate zinc acetate from zinc sulfate, zinc oxide or a dilution.

In one line

Identity is the zinc figure, the acetate figure and the water figure agreeing on the same dihydrate, with the solid-state pattern as the tie-breaker.

Identity evidence, layer by layer

A certificate can carry the right name and still not demonstrate it. Each layer below is a separate question with its own evidence, and an answer that stops at the first layer describes paperwork, not powder.

Identity evidence for zinc acetate dihydrate
LayerQuestionTestWhat it proves
DocumentIs the hydrate and salt named?Name, CAS number, formulaPaperwork only
ZincIs the zinc figure right?Complexometric titration (EDTA)The zinc content, not the salt
AcetateIs the anion acetate?Acetate reaction, IR, ion chromatographyThe salt, and the 1:2 ratio
WaterIs it the dihydrate?Karl FischerThe hydration state
Solid stateIs the crystal the dihydrate?FTIR, and XRD for a disputeThe hydrate as a solid

The catalog identity is “zinc and acetate conform”. That is a reasonable release gate, but it does not report the water or the acetate as numbers. When the salt is disputed, ask for the Karl Fischer result, the acetate result and the diffraction pattern; a conformity statement is not a measurement.

The zinc, acetate and water ratio

The formula fixes the mass balance. In 100 g of pure C4H6O4Zn·2H2O there are 29.8 g of zinc, 53.8 g of acetate and 16.4 g of water. The zinc-to-acetate mass ratio is 29.8 ÷ 53.8 = 0.554, and the molar ratio is 1:2. The zinc figure and the assay expressed as the dihydrate are related by 219.50 ÷ 65.38 = 3.357, so 30.0% zinc is about 100.7% of the dihydrate formula.

The catalog ranges sit on that balance. Zinc 29.0–32.0% with water 10.0–14.0% describes a dihydrate that has lost part of its crystal water: at 12% water the zinc works out near 31.3%, and at 10% it is near 32.1%. A lot with 29.0% zinc and 14.0% water is closer to the full hydrate. Neither is a purity failure; the pair has to be read together.

A blend is caught by the same ratio. A powder made from zinc acetate and zinc sulfate can be formulated to land inside the zinc range, but the sulfate test turns positive and the acetate result falls below the 1:2 ratio. A blend with zinc oxide raises the zinc figure and leaves an insoluble residue; a dilution lowers both zinc and acetate and raises the water. The assay sees the zinc; the acetate and water see the rest of the salt.

FTIR and XRD: the solid-state check

FTIR is the routine identity test because it sees the acetate carboxylate bands and the water bands in one spectrum. It can separate the acetate from the sulfate, the gluconate and the citrate when the spectrum is compared with a named reference. The release identity should name the reference material and the band region used, not only the word “conforms”.

X-ray diffraction answers the hydrate question more directly. Zinc acetate dihydrate, the anhydrous salt and zinc sulfate heptahydrate have different unit cells, so their peak positions differ, and a mixture shows both sets of peaks. XRD is not a purity assay and it does not measure the water content, but it is the strongest evidence that the crystal in the drum is the hydrate named on the certificate. Ask for the reference pattern and a stated detection limit before reading a “match” statement.

What substitution looks like

Substitutions and the signals on a zinc acetate certificate
SubstitutionWhat it changesSignalTest
Zinc sulfateSulfate present; lower pH; acetate absentPositive sulfate test; pH 4.4–5.6; acetate lowIon chromatography, pH, FTIR
Zinc oxideInsoluble zinc; acetate lowResidue in water; zinc high; acetate lowSolubility, assay, XRD
Zinc gluconate or citrateDifferent anion; different IRAcetate absent; different spectrumAcetate test, FTIR, ion chromatography
DilutionZinc and acetate down; water upMass balance short; assay lowMass balance, Karl Fischer
Surface moistureWater up; zinc per gram downWater above 14.0%; cakingKarl Fischer, sieve
Technical gradeHeavy metals upPb, Cd or As above the agreed limitICP-MS

Appearance and odour are weak signals. A white powder can be the acetate, the sulfate or an oxide; a faint acetic note is consistent with the acetate but is not a measurement. The stronger signals are the acetate test, the sulfate test, the zinc figure and the mass balance. A certificate that reports appearance and assay but not the anion has left the most likely substitution untested.

Identity lines for the specification

  • “Zinc acetate dihydrate, C4H6O4Zn·2H2O, CAS 5970-45-6.”
  • “Assay 99.0–101.0% by complexometric titration; state the basis.”
  • “Zinc 29.0–32.0%; water 10.0–14.0% by Karl Fischer.”
  • “Identification: zinc reaction, acetate reaction and IR against a named reference.”
  • “Sulfate by ion chromatography: report the result where the salt is disputed.”
  • “≥95% through 80 mesh; heavy metals and microbiology as catalog.”
  • “No substitution with another zinc salt or oxide without written change control.”

Five questions before approval

  1. Which hydrate and CAS number are on the certificate?
  2. What are the zinc, water and acetate results, and which methods produced them?
  3. What does the IR spectrum show, and is the sulfate test negative?
  4. Can you provide the XRD pattern and the reference used for the dihydrate?
  5. Would you agree to a joint re-test of the retained sample if the lot is challenged?

Five direct answers amount to an identity file; a single assay percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits; the grades page compares the salts; the acetate versus sulfate page covers the label consequences; the analytical methods library explains the tests.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation