06 Identity & adulteration

How we prove a sodium selenite lot is the anhydrous salt

Technical document 06 · Reviewed 2026-11-19 · Sodium Selenite

On this page
  1. The four identity layers
  2. The selenium and sodium balance
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. What to write into the specification
  6. Five questions for the supplier

A lot is anhydrous sodium selenite when five lines agree: the document names the anhydrous salt and CAS 10102-18-8, infrared and titration identify the salt, the iodometric assay is 98.0–101.0%, the selenium figure is 44.0–46.0%, and the loss on drying is ≤2.0% with sodium near the theoretical 26.6%. The assay alone cannot separate the salt from the pentahydrate, a dilution or a selenate mix. The hydrate and the oxidation state are the two questions that need their own evidence.

In one line

Identity is the agreement between the titration assay, the selenium figure and the water content, with the hydrate state named in the specification.

The four identity layers

A certificate can name the right salt and still describe the wrong hydrate. The four layers below are separate questions, and each one needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.

Four layers of sodium selenite identity
LayerQuestionTestWhat it proves
DocumentIs the hydrate and CAS named?Name, CAS number, formulaPaperwork only
SaltIs it sodium selenite?Infrared and iodometric titrationThe selenite salt
ElementDoes the selenium balance close?Se from titration; total Se by ICP-MSThe selenium figure
WaterIs it the anhydrous salt?Loss on drying; XRD if disputedThe hydrate state

The order matters. The document layer is a purchase-order check, not an identity test. The salt layer is the first analytical evidence; the element and water layers are what turn a name into a specification.

The selenium and sodium balance

Anhydrous sodium selenite is 45.66% selenium and 26.59% sodium by mass, with two sodium ions for each selenium atom. A lot with a 99.0% assay should carry about 45.2% selenium and about 26.3% sodium on the same basis. The sodium figure is not on the catalog specification, so it is an additional test; ask for it when the salt or the hydrate is disputed.

The sodium-to-selenium ratio is consistent with the disodium salt, but it does not prove the oxidation state. Sodium selenate is also a disodium salt with a similar selenium-to-sodium mass ratio, so a sodium result close to theory does not rule out selenate. The titration does: it measures selenite, and selenate does not titrate under the same conditions. If the ICP-MS total selenium is higher than the titration-derived figure, the gap is the evidence for another species.

The absolute figures catch a dilution. A non-sodium carrier lowers the sodium figure and the assay together; sodium chloride or sulfate raises sodium relative to selenium. Neither pattern is proof on its own, but both tell the reviewer which second test to order. The ratio and the absolute figures answer different questions, and a certificate needs both.

X-ray diffraction and the solid state

X-ray diffraction answers the solid-state question: is the powder crystalline, and does the pattern match the anhydrous salt? It can distinguish the anhydrous pattern from the pentahydrate and from an amorphous carrier, and it can compare lots from two sources. It is not a purity assay, and it does not measure the counter-ion or the oxidation state.

XRD is not a routine release test for this product. Ask for the reference pattern and the detection limit before reading a “match” statement, and read a certificate that reports only “XRD conforms” as a pointer, not as evidence. The release tests remain infrared, titration, loss on drying, metals and microbiology.

The method is most useful when the question is the hydrate. A lot with a selenium figure near 44% and a loss on drying near 2.0% is consistent with the anhydrous salt; a pattern that matches the pentahydrate would explain a selenium figure near 30% and a water content near 34% without any need to invent a blend.

What adulteration looks like

Common sodium selenite substitutions and the signals
AdulterantWhat it doesSignalTest
PentahydrateLowers Se to about 30%; raises water to about 34%Se and loss on drying far outside the rangesLoss on drying, Se, XRD
Sodium selenateDifferent oxidation state; similar Se : Na ratioTitration low against ICP-MS total SeIon chromatography, ICP-MS
Non-sodium diluentLowers assay and Se; sodium below theoryAbsolute Se and Na both lowSodium by ICP-OES, mass balance
Sodium chloride or sulfateRaises sodium relative to Se; lowers assayNa high; Se lowIon chromatography, sodium
Elemental seleniumInsoluble; red or grey; low titrationColour; residue; low assayVisual, filtration, titration, XRD

Colour is the weakest signal. A pink or red tint can be elemental selenium, but it can also be a trace impurity or a lighting artefact. The stronger signals are the water content, the selenium-to-sodium balance and the titration against total selenium. A certificate that reports appearance and assay but not the hydrate has left the most likely substitution untested.

What to write into the specification

  • “Sodium selenite, anhydrous, CAS 10102-18-8, Na2SeO3; the pentahydrate is excluded.”
  • “Assay 98.0–101.0% by iodometric titration, with the basis stated.”
  • “Selenium 44.0–46.0%, reported from the titration; total selenium by ICP-MS where the form is disputed.”
  • “Loss on drying ≤2.0%.”
  • “Identification by infrared and titration; sodium about 26.6% by ICP-OES if the salt is to be confirmed analytically.”
  • “No selenate above the agreed limit; ion chromatography where a blend is suspected.”
  • “Heavy metals and microbiology as listed; destination market confirmed before the order.”

The word “anhydrous” does the work that a selenium range alone cannot do. A specification that omits it admits the pentahydrate, and a specification that omits the oxidation state admits selenate. Both substitutions can land inside a broad selenium range if the rest of the specification is silent.

Five questions for the supplier

  1. Which hydrate is this lot, and which CAS number is on the certificate?
  2. Can you provide the infrared spectrum and the titration method, not only the assay percentage?
  3. What is the loss on drying for this lot, and is the assay reported as-is or on the dried basis?
  4. What is the total selenium by ICP-MS, and does it agree with the titration-derived figure?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file. A single assay percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grade page compares the hydrate and the trituration; the selenite and selenomethionine comparison covers the source question; the methods library explains the separation; the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation