Sodium selenite grades: anhydrous, pentahydrate and trituration
Sodium selenite is sold in four presentations that are easy to confuse: the anhydrous salt, the pentahydrate, a trituration on a carrier, and a granulated powder. The catalog article is the anhydrous salt, CAS 10102-18-8, at 44.0–46.0% selenium; the pentahydrate is a different CAS with about 30% selenium, and a trituration is a different article with a declared carrier. The presentation decides the weighing step, the fill weight and the label before it decides anything else.
The hydrate and the presentation are the grade: the same salt name can describe 45.7% selenium, 30.0% selenium, or a trituration with a carrier on the label.
Why the presentation is the grade
Sodium selenite is one chemical compound, so there is no purity ladder to choose from in the way there is for a plant extract. What a buyer chooses is the hydrate and the presentation: the anhydrous salt, the pentahydrate, a dilution on a carrier, or a granulated powder. Each variation changes a number the buyer relies on — selenium content, loss on drying, flow, or the mass that carries the dose.
The anhydrous salt is the catalog article. The pentahydrate is not a wetter version of the same powder; it is a different molecular weight, a different CAS number and a different selenium figure. A trituration is the salt distributed on a carrier, usually because the dose is too small to weigh into a production blend. Granulation changes the particle size and the flow without changing the chemistry.
A purchase order that says “sodium selenite” and nothing else has not chosen among them. The hydrate, the carrier and the particle form are the three variables that travel from the specification to the label.
The four presentations side by side
| Presentation | Identity | Selenium | Water | What changes |
|---|---|---|---|---|
| Anhydrous salt | CAS 10102-18-8; Na2SeO3 | 44.0–46.0% | Loss on drying ≤2.0% | The catalog article |
| Pentahydrate | CAS 26970-82-1; Na2SeO3·5H2O | About 30.0% | About 34% water | Different CAS, dose mass and label name |
| Trituration | Salt plus a named carrier | Declared on the blend | Carrier-dependent | The carrier is an ingredient; the label and dose change |
| Granulated powder | The same salt, larger particles | Same as the base salt | Same limit | Flow and dust change; the assay does not |
The CAS number is the fastest check. A certificate that says 10102-18-8 describes the anhydrous salt; one that says 26970-82-1 describes the pentahydrate. A certificate that names only a carrier is a certificate for a trituration, and the selenium figure belongs to the blend, not to the salt. The four rows are four different purchase orders, not four grades of one specification.
Solubility, moisture and dust
Anhydrous sodium selenite is a white to off-white powder, freely soluble in water; the solution is neutral to slightly alkaline. It is hygroscopic, so the powder picks up moisture when the pack is open, and it is an oxidant that reacts with reducing agents. Those two properties drive the handling: a sealed pack, a dry store, and a weighing step that keeps the salt away from ascorbic acid, thiols and sulfites.
The pentahydrate is a different solid with a different water content and a different solubility behaviour. It is not interchangeable with the anhydrous article, and a formula written for one cannot be switched to the other without recalculating the mass. The selenium figure differs by about a third, so the error from a silent substitution is large.
Granulation improves flow and reduces dust, which matters at a weighing station where the active is a small fraction of the blend. It does not change the assay, and it does not make the salt less hygroscopic. Dust control is a containment question as well as a housekeeping one: the concentrated salt is toxic by ingestion, so the SDS and the weighing controls belong in the file.
Dose arithmetic and the dosage form
The label dose is selenium, not salt. At 55 µg selenium the anhydrous salt supplies about 0.12 mg and the pentahydrate about 0.18 mg; at 200 µg the figures are about 0.44 mg and 0.67 mg. A trituration changes the mass again, because the carrier dilutes the selenium figure. The arithmetic is fixed by the formula and the hydrate, not by the brand name on the pack.
| Selenium dose | Anhydrous salt (45.66% Se) | Pentahydrate (30.02% Se) |
|---|---|---|
| 55 µg | About 0.12 mg | About 0.18 mg |
| 100 µg | About 0.22 mg | About 0.33 mg |
| 200 µg | About 0.44 mg | About 0.67 mg |
At these masses the pure salt is a premix ingredient, not a weigh-out ingredient for a production blend. A trituration turns a sub-milligram quantity into grams: a 0.1% selenium blend needs 55 mg to deliver 55 µg. The trade is that the carrier becomes part of the article, the selenium figure falls, and the label has to declare the blend rather than the pure salt.
The dosage form follows. A capsule or tablet can take the pure salt only through a premix step; a stick pack or a powder blend usually takes a trituration. A liquid uses the salt because it dissolves, but the solution needs its own stability data. The presentation is a formulation decision, and it should be made before the fill weight is fixed.
What to write into the specification
- “Sodium selenite, anhydrous, CAS 10102-18-8, Na2SeO3; the pentahydrate is excluded.”
- “Assay 98.0–101.0% by iodometric titration, with the basis stated.”
- “Selenium 44.0–46.0%, reported from the titration; total selenium by ICP-MS where the form is disputed.”
- “Loss on drying ≤2.0%; a hydrate outside this limit is a different article.”
- “Identification by infrared and titration; no selenate above the agreed limit.”
- “For a trituration: carrier named, selenium figure on the diluted material, and the carrier declared on the label.”
- “For granulation: particle-size range and bulk density agreed; the chemistry is unchanged.”
- “Destination market and exact hydrate confirmed before the order.”
A specification that names only the salt and the assay leaves the hydrate, the carrier and the presentation open. Those are the three variables that change the dose and the label, and they are cheaper to fix before the order than after it. The product hub carries the catalog specification; the selenite and selenomethionine comparison takes the source question further; the L-selenomethionine page and the selenium yeast page show the other two sources; the compliance page covers the label entries; the quality page describes the release workflow.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation