06 Identity & adulteration

How to prove a sodium molybdate lot is the anhydrous salt

Technical document 06 · Reviewed 2026-11-19 · Sodium Molybdate

On this page
  1. The identity layers
  2. The molybdenum and sodium ratio
  3. X-ray diffraction and the solid form
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A sodium molybdate lot is the anhydrous salt when the document names the hydrate and the CAS number, the molybdenum figure sits at 45–47%, sodium is near 22.3%, loss on drying is at or below 1.0% and the diffraction pattern matches the anhydrous reference. No single number proves it; the figures have to agree.

In one line

Identity is a set of agreeing figures: the molybdenum and sodium results fix the salt, the loss on drying fixes the hydrate, and the diffraction pattern fixes the solid form.

The identity layers

A certificate can carry the right name and still fail to prove the powder. The layers below are separate questions, and each one needs its own evidence. A supplier who answers the first has described the paperwork, not the material.

Layers of sodium molybdate identity
LayerQuestionTestWhat it proves
DocumentIs the hydrate named?Name, CAS number, formulaPaperwork only
StoichiometryIs the molybdenum figure right?Complexometric titration or ICP-OESThe element, not the salt
Counter-ionIs it the sodium salt?Sodium by ICP-OESThe salt form
HydrateAnhydrous or dihydrate?Loss on dryingThe water of crystallisation
Solid formDoes the phase match?X-ray diffraction and infraredThe crystalline reference

The molybdenum figure alone cannot separate the salt from a blend or from a different molybdenum compound. The sodium figure alone cannot tell you how much molybdenum is present. The loss on drying alone cannot tell you whether the water is crystal water or surface moisture. Together they narrow the answer quickly.

The molybdenum and sodium ratio

Anhydrous sodium molybdate, Na2MoO4, is 46.6% molybdenum and 22.3% sodium by mass, a molar ratio of two sodium to one molybdenum. A certificate that reports 46.0% molybdenum should sit near 22.0% sodium; a sodium result around 20% points to a dilution, and a result above 23% points to another sodium salt or a sodium-bearing carrier. The ratio is a stronger identity check than either figure alone.

It also catches a blend that the molybdenum assay would pass. A mixture of sodium molybdate and molybdenum trioxide, which is 66.7% molybdenum, can be built to land inside the 45–47% window while the sodium falls below the theoretical figure. The assay sees molybdenum; the counter-ion sees the salt. This is why the sodium test is worth ordering for a new source even though it is not a routine release line.

Reconcile the two potency rows as well. A 99.0% salt assay at the theoretical 46.6% molybdenum gives 46.1% molybdenum; a 101.0% assay gives 47.1%. A lot whose assay and molybdenum sit at opposite edges of their ranges is describing two different things, and the basis is the first place to look.

X-ray diffraction and the solid form

X-ray diffraction answers the question that the chemical assays cannot: which crystalline phase is in the drum. The anhydrous salt and the dihydrate give different patterns, so a diffraction scan separates them directly, without inferring the hydrate from the moisture figure. For a disputed lot, the pattern is the cleanest evidence of what was packed.

Infrared, the catalog identification method, also carries hydrate information: the O-H stretching region shows whether water of crystallisation is present, and the molybdate bands confirm the anion. Infrared is a good release identity test, but it is less direct than diffraction when the question is the phase. Ask for the reference pattern and the detection limit before accepting a match statement; a report that says only “XRD conforms” has added little.

Diffraction is not a purity assay. It will not report the molybdenum percentage, the sodium percentage or a trace metal, and an amorphous impurity can sit outside the pattern. Use it with the chemical figures, not instead of them.

What adulteration looks like

Substitutions and the signals that expose them
AdulterantWhat it doesSignalTest
Dihydrate sold as anhydrousWaters the salt; lowers molybdenum per gramLoss on drying near 15%; molybdenum near 39.7%Loss on drying, molybdenum, XRD
Molybdenum trioxideRaises molybdenum above the range; insolubleResidue in water; sodium below 22%Solubility, sodium, XRD
Sodium tungstateSame group; similar white saltTungsten by ICP-MS; mass balance offICP-MS with tungsten reported
Chloride or sulfate dilutionLowers molybdenum; adds anionsMolybdenum below 45%; high ash or conductivityIon chromatography, ICP-OES
Recycled catalyst residueAdds cobalt, nickel, vanadium or tungstenExtra metals at mg/kgFull ICP-MS scan

Tungsten is the hardest substitution because it sits directly below molybdenum in the periodic table and behaves similarly in solution. A total-molybdenum titration that does not separate the two can read tungsten as molybdenum. ICP-MS reports both elements separately, which is why the full scan belongs in a source-qualification file.

How to write identity into the specification

  • “Sodium molybdate, anhydrous, CAS 10141-05-6, Na2MoO4.”
  • “Assay 99.0–101.0% by HPLC; molybdenum 45.0–47.0% by complexometric titration.”
  • “Loss on drying ≤1.0%; identification by infrared and HPLC.”
  • “Sodium about 22.3% by ICP-OES where the salt form is confirmed analytically.”
  • “X-ray diffraction consistent with the anhydrous reference for a disputed lot.”
  • “Tungsten and other catalyst metals reported at the agreed limit.”
  • “Particle size ≥95% through 40 mesh.”

Five questions for the supplier

  1. Which hydrate is this lot, and which CAS number is on the certificate?
  2. What is the molybdenum result, and is the assay reported on the same basis?
  3. What is the sodium result by ICP-OES, and what method was used?
  4. What is the loss on drying, and does the diffraction pattern match the anhydrous reference?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample with a full metal scan?

Five direct answers amount to an identity file; a single assay percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits; the grades page compares the hydrates; the XRD method note explains the phase check; the ICP-MS note covers the trace-metal scan; the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation