02 Grade comparison

Sodium molybdate grades: anhydrous, dihydrate and the mesh

Technical document 02 · Reviewed 2026-11-19 · Sodium Molybdate

On this page
  1. Why one name covers several grades
  2. The grades side by side
  3. Powder, granulate and solution behaviour
  4. Dose arithmetic and the fill
  5. What to write into the specification
  6. When the other grade is the wrong choice

Sodium molybdate is supplied as the anhydrous salt or the dihydrate, and as a 40 mesh powder, a granulate or a diluted blend. The hydrate sets the molybdenum figure per gram — about 46.6% for the anhydrous salt and 39.7% for the dihydrate — so the grade choice is a dose and label decision before it is a flow decision.

In one line

The grade decision is the hydrate state and the particle form: they set the molybdenum figure per gram, the water limit and how the powder behaves in a blend.

Why one name covers several grades

The catalog form is the anhydrous salt, Na2MoO4, as a 40 mesh powder with a loss on drying of 1.0% or less. The dihydrate, Na2MoO4·2H2O, is the form most often seen in commerce, and it carries less molybdenum per gram because the water of crystallisation is part of the weighed mass. Both are called sodium molybdate. Only the CAS number and the molybdenum figure separate them.

Particle form is the second decision. A fine powder blends evenly but can dust and cake; a granulate flows better and wets more slowly; a diluted blend makes a very small dose weighable. None of these changes the salt chemistry, but each changes the specification line, the label and the weighing step.

The grades side by side

Sodium molybdate grades compared
PropertyAnhydrousDihydrateDiluted blend
CAS number10141-05-610102-40-6Salt CAS plus a named carrier
FormulaNa2MoO4Na2MoO4·2H2OSalt plus carrier
Molar mass205.92241.95—
Molybdenum45.0–47.0% (theoretical 46.6%)About 39.7%By declaration
WaterLoss on drying ≤1.0%About 14.9% water of crystallisationCarrier-dependent
AppearanceWhite crystalline powderWhite crystals or powderWhite to off-white powder
Usual roleCapsules, tablets, dry blendsBulk chemical use; not the catalog gradeLow-dose blending

The two CAS numbers are a purchase-order issue. An order that says sodium molybdate without the hydrate and the CAS has not specified the material, and the molybdenum result is the fastest way to see which one arrived. For the same weight, the dihydrate delivers about 15% less molybdenum than the anhydrous salt, which is enough to move a label claim.

Powder, granulate and solution behaviour

The anhydrous powder is freely soluble in water and gives a solution that is neutral to slightly alkaline. It is also hygroscopic: an opened pouch takes up moisture, the loss on drying rises and the powder can cake. The dihydrate is the more hydrated form and does not pick up water in the same way, but it cannot meet the ≤1.0% loss-on-drying line of the catalog grade.

At 40 mesh the powder is fine enough to blend into a dry mix and coarse enough to handle without excessive dust. A granulated grade is supplied on request for flow and dust control; it should still be specified by mesh, because granulated is a process word, not a particle-size result. A diluted blend adds a carrier, and that carrier is an ingredient on the label and a variable in the assay.

Solution pH deserves a line in the specification if the material is used in a liquid. At neutral to slightly alkaline pH the molybdate ion stays in its simple form; as the pH falls, it condenses into polymolybdates, and the behaviour of the solution changes. The powder grade does not fix that risk, but the formulator should know it before choosing a matrix.

Dose arithmetic and the fill

The label declares elemental molybdenum, so the salt mass per dose is the declared figure divided by the molybdenum fraction. The table uses the theoretical figures; a batch works from its certificate result.

Salt mass needed for a target molybdenum dose
Elemental molybdenumAnhydrous saltDihydrate salt
50 µgAbout 107 µgAbout 126 µg
100 µgAbout 215 µgAbout 252 µg
500 µgAbout 1,073 µgAbout 1,261 µg

The EU nutrient reference value for molybdenum is 50 µg and the US Daily Value is 45 µg, so a 100 µg dose is roughly twice either reference. The EU upper level for adults is 600 µg a day, which a 500 µg supplement approaches once the diet is counted; the total intake, not the capsule alone, is the number to review.

At these masses the salt is a minor part of any capsule. A 100 µg dose is about 215 µg of anhydrous salt, which is 0.04% of a 500 mg fill. Direct weighing at that ratio is not practical, so the grade that matters is often a trituration: a 1% blend puts 21.5 mg of powder in the capsule, and a 0.1% blend puts 215 mg. The carrier, the blend uniformity and the label all follow that choice.

What to write into the specification

  • “Sodium molybdate, anhydrous, CAS 10141-05-6, Na2MoO4.”
  • “Assay 99.0–101.0% by HPLC; molybdenum 45.0–47.0% by complexometric titration.”
  • “Loss on drying ≤1.0%; identification by infrared and HPLC.”
  • “Particle size ≥95% through 40 mesh; granulated grade by agreement.”
  • “Heavy metals and microbiology as listed; sodium about 22.3% where the salt form is checked.”
  • “Hydrate state, carrier and dilution ratio named whenever the grade is not the anhydrous powder.”

A specification that names only sodium molybdate leaves the hydrate, the mesh and the carrier open. Those three lines decide the molybdenum per gram, the flow and the label, so they belong in the specification rather than in an email.

When the other grade is the wrong choice

If the label declares the anhydrous salt, the dihydrate is not a drop-in: the mass changes and the declared molybdenum no longer matches the weigh-up. If the formula is a dry blend that will be stored open, the hygroscopic anhydrous powder needs a pack that keeps moisture out, and a granulate may handle better. If the market file or the label does not accept the carrier, a diluted blend is the wrong route however convenient the weighing becomes. The grade is part of the product identity, not a packing preference.

The catalog specification sits on the sodium molybdate product page. The salt and the chelate are compared on the level-four page; the certificate lines are explained on the COA page; the moisture and pack questions are on the stability page; the diffraction check that separates the hydrates is described in the XRD method note.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation