01 COA & batch testing

What the COA for L-selenomethionine actually contains

Technical document 01 · Reviewed 2026-11-19 · L-Selenomethionine

On this page
  1. The certificate as a parameter list
  2. What the two percentages measure
  3. Release limit, result and basis
  4. What moves between batches
  5. When an outside test earns its place
  6. What to compare between suppliers

For an L-selenomethionine lot the certificate reports appearance, identification by infrared, assay by HPLC on the as-is basis, selenium by ICP-MS, specific rotation, loss on drying, particle size, the heavy-metal panel and microbiology. Each line needs its method, its release limit, and the lot's own result beside that limit. The figures here are the catalog specification; the batch COA confirms a particular drum.

In one line

The selenium figure shows how much of the element is there; the rotation shows which enantiomer carries it, and a certificate needs both.

The certificate as a parameter list

A certificate is useful when it can be audited line by line. Three things have to sit beside every parameter: what was measured, which method produced the number, and which limit the lot was released against. Without all three, the line is a statement of intent rather than a result.

Identity, selenium and physical limits · L-selenomethionine
ParameterMethodRelease limit
AppearanceVisualWhite to off-white crystalline powder
IdentificationIR against a reference spectrumConforms
Assay (as-is basis)HPLC97.0–103.0%
Selenium (Se)ICP-MS39.0–41.0%
Specific rotationPolarimetry+17.0° to +19.5°
Loss on dryingGravimetric≤0.5%
Particle sizeSieve analysis≥95% through 40 mesh
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent

What the two percentages measure

The assay counts the molecule; the selenium figure counts one atom inside it. They are produced by different instruments and answer different questions, and that is why the pair is more informative than either line alone.

The arithmetic connects them. L-selenomethionine has a molar mass of about 196.1 g/mol and carries one selenium atom at 78.97 g/mol, so the element is 40.3% of the molecule by mass at full purity. Multiply the assay by that fraction and you should land inside the selenium window: 97.0% assay implies about 39.1% selenium, and 41.0% selenium implies about 101.8% assay. A lot reported at 103.0% assay and 41.0% selenium is not describing one pure substance on both lines; either the two figures sit on different bases, or they were measured on different samples.

The assay is reported as-is, which is why loss on drying belongs beside it. With a limit of ≤0.5% the gap between the as-is and dried bases is at most half a percentage point. A certificate that reports an as-is assay and no moisture figure has left the reader unable to convert.

Neither figure can see chirality. The D enantiomer carries the same 40.3% selenium and the same retention time on an achiral column, so a half-racemised lot still passes both lines. That is the gap the specific rotation fills.

Release limit, result and basis

The release limit is the boundary for the lot; the batch result is what the laboratory measured. The two belong side by side on the page. A result column that repeats the specification range is not a result; it is a copy of the gate.

Lines that must be lot-specific on the certificate
LineWhat a copied limit looks likeWhat a real result looks like
AssayThe window printed as the resultOne figure, with the method and the basis named
SeleniumLeft blank, or “conforms”A figure from ICP-MS, with the isotope and the digestion named
Specific rotation“+17.0° to +19.5°” in the result cellA value with temperature, concentration, solvent and wavelength
Loss on dryingAbsentA figure, because it converts the assay to the dried basis
Microbiology“Absent” with no methodCounts and absence tests, with the method named
Retest dateAbsentA date that matches the label on the pack

The rotation line deserves a second look. A value of +18.2° without its conditions cannot be compared with another laboratory's figure, and a value written as a range is a specification, not a measurement. Rotation depends on concentration, solvent, temperature and path length.

What moves between batches

Assay and selenium move together, because both respond to purity and to dilution. If the selenium result falls to 39.2% and the assay stays at 99%, the likely cause is a diluent that carries no selenium — the sulfur analogue methionine is the closest and most obvious one, since it is a white crystalline solid of similar solubility. The selenium figure is the screen for that route; the assay alone will not find it if the method does not separate the two amino acids.

Rotation moves independently. A low rotation with a normal selenium figure points to racemisation rather than to dilution, and racemisation is a process problem: a hot alkaline step, a long hold at high pH or an aggressive hydrolysis will pull the optical purity down while every elemental figure stays in range.

Loss on drying follows the drying step and the pack, not the assay. Particle size and flow move with milling and sieving, and colour moves with the drying history rather than with the assay. A trend across consecutive lots — selenium drifting down, rotation drifting toward the bottom of the window — says more than a single result near an edge.

When an outside test earns its place

Order an independent test for a new source, a first shipment into a regulated market, a rotation result near the lower limit, a speciation claim that the certificate does not support, or a disputed result. What the outside panel adds is the tests that separate forms: chiral HPLC or chiral derivatisation for the enantiomeric ratio, ICP-MS for selenium and for the heavy-metal panel, IR for the solid, and polarimetry repeated under declared conditions.

Ask the laboratory to report its limit of quantification for the chiral method. A line that reads “D form not detected” without a limit says something about the method's sensitivity, not about the sample. Give the referee the retained sample and the specification, and ask for the tests that distinguish the L form from the alternatives.

What to compare between suppliers

Put six lines side by side: the declared form and whether the lot is synthetic or fermentation-derived; the assay result, its basis and its method; the selenium result and the ICP-MS conditions; the rotation value with its measurement conditions; loss on drying; and the chiral purity, if a figure is offered at all. Two quotations that agree on selenium and diverge on the other five are not describing the same powder.

The second layer is traceability. The lot code should be identical on the certificate, the pack and the retained sample, and the certificate should say who manufactured the lot. A certificate can be entirely correct and still describe a drum other than the one that arrives.

The specification sits on the L-selenomethionine product page. The form question is set out on the grade page; the evidence that separates the L form from its mirror image is on the identity page. The two instruments behind the certificate are described in the HPLC and ICP-MS method notes.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation