06 Identity & adulteration

How we prove a potassium gluconate lot is the named salt

Technical document 06 · Reviewed 2026-11-19 · Potassium Gluconate

On this page
  1. Four questions, four pieces of evidence
  2. The 16.69% check
  3. Where X-ray diffraction fits
  4. Signals of substitution
  5. Specification wording
  6. Five questions for the supplier

Potassium gluconate can be identified with equipment most contract laboratories already have. Infrared spectroscopy shows the gluconate anion; a titration measures the salt; the potassium figure should land near 16.69%; and water explains the difference between the dried and as-received results. The four measurements together are stronger than any single assay percentage.

In one line

Identity is three agreeing measurements — the infrared spectrum, the gluconate titration and a potassium figure close to 16.7% — plus a water result that closes the mass balance.

Four questions, four pieces of evidence

A supplier can name the salt correctly and still ship a blend, and a titration can sit in range while the cation is wrong. The layers below are independent, so each row needs its own result rather than a shared “conforms”.

Four layers of potassium gluconate identity
LayerQuestionTestWhat it proves
DocumentIs the salt named?Name, CAS number, formulaPaperwork only
InfraredIs the solid the gluconate?FTIR against a reference spectrumThe anion, in the solid state
TitrationHow much salt is present?Titration for the gluconateQuantity, not identity
PotassiumIs the cation potassium?Titration, flame photometry or ICP-OESThe element
WaterIs the mass balance consistent?Loss on dryingWhether the assay figures add up

The 16.69% check

The formula gives the expected potassium. C6H11KO7 weighs 234.25 g/mol, potassium contributes 39.10, and the ratio is 16.69%. A salt assay of 99.0–101.0% therefore corresponds to 16.52–16.86% potassium. If the reported figure sits far outside that band, either the assay, the potassium method or the identity of the material is wrong.

Different salts move the figure in different directions. Potassium citrate monohydrate carries about 36.16% potassium and potassium chloride about 52.4%, so either would push the result up. Sodium gluconate keeps the anion but replaces the cation, so the potassium figure falls while sodium rises. A dextrose or maltodextrin dilution lowers the assay and the potassium together.

Work an example. A potassium result of 15.0% implies a salt content of about 89.9% if all the potassium comes from the gluconate, which is below the assay floor. A result of 17.0% implies about 101.8%, above the ceiling. Either edge is a prompt to read the method and the water, not an automatic reject.

Where X-ray diffraction fits

X-ray diffraction sees the crystal lattice, not the potassium. It can show that a lot is crystalline, compare it with a reference pattern, or detect an amorphous carrier in a blend. It is not a release test here, and a “conforms” line without the pattern and the reference proves very little.

Use XRD when the question is solid form: a suspect blend, a new source, or a lot that behaves differently on the press. Pair it with FTIR for the anion and titration for the cation. The three methods answer three different questions, and none of them is a substitute for the others.

Signals of substitution

Common potassium gluconate substitutions and the signals
AdulterantWhat it doesSignalTest
Dextrose or maltodextrinDilutes the saltAssay and potassium both low; water may riseAssay, potassium, FTIR
Sodium gluconateSame anion, different cationPotassium low; sodium highPotassium and sodium by ICP-OES
Potassium citrateDifferent anion, more potassiumPotassium far above 16.7%; alkaline solutionPotassium, FTIR, citrate test
Potassium chlorideMuch more potassium per gramPotassium above 20%; chloride presentPotassium, chloride test, FTIR
WaterLowers the as-received assayLoss on drying high; dried assay normalLoss on drying

Colour is the weakest clue: white to off-white covers too much ground. The potassium figure, the infrared spectrum and the mass balance are the useful signals. A certificate with appearance and assay but no identity has not tested the most likely substitution.

Specification wording

  • “Potassium gluconate, CAS 299-27-4, C6H11KO7.”
  • “Assay 99.0–101.0% by titration, with the dried or as-is basis stated.”
  • “Potassium 16.0–17.0% by titration; report the method and the basis.”
  • “Identification by infrared against a reference spectrum, and by titration.”
  • “Loss on drying ≤1.0%; particle size ≥95% through 40 mesh.”
  • “No sodium gluconate, potassium citrate or potassium chloride above the stated limit.”

Five questions for the supplier

  1. Which salt is this lot, and which CAS number appears on the certificate?
  2. Can you provide the infrared spectrum, not only an “identity conforms” line?
  3. What are the assay and potassium results, and on which basis were they calculated?
  4. What is the loss on drying for this lot, and how does it close the mass balance?
  5. If the results are contested, will you re-test the retained sample jointly with us?

Five answers of that kind make a file that can be audited; one assay number cannot. Catalog limits sit on the product hub; the certificate layout is explained on the COA page; powder options are on the grades page; the FTIR method note explains what an infrared match can and cannot prove; the XRD note covers the solid-state check; and the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation