06 Identity & adulteration

How we prove a manganese sulfate lot is the monohydrate

Technical document 06 · Reviewed 2026-11-19 · Manganese Sulfate

On this page
  1. Four checks, one identity
  2. The manganese-to-assay ratio
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. Writing identity into the specification
  6. Five questions for the supplier

A manganese sulfate lot is the monohydrate when four lines agree: the document names the hydrate and CAS 10034-96-5, IR and titration match the reference, the manganese figure is 31.5–33.0% with an assay of at least 98.0%, and water by Karl Fischer is 10.0–12.0%. The manganese figure alone cannot separate the monohydrate from the anhydrous salt, because a monohydrate result calculated on a water-free basis also lands near 36%. The water result and the basis line are what close the identification.

In one line

Identity is the agreement between the manganese figure, the water and the hydrate name; any one of them alone can describe a different salt.

Four checks, one identity

Identity is not one test. It is four answers that have to agree, and each answer rules out a different mistake. The document layer rules out a naming error. IR rules out the wrong salt family. Titration measures the metal and the monohydrate. Karl Fischer decides which hydrate was on the balance. A supplier who supplies only the first answer has supplied a label, not evidence.

Four checks that together identify the monohydrate
CheckQuestion it answersMethodWhat it establishes
DocumentIs the hydrate named?Name, CAS number, formulaPaperwork only
SpectroscopyAre sulfate and water present?IR spectrumThe salt family and the hydrate
TitrationHow much manganese and monohydrate?Complexometric titrationThe metal and the assay
WaterWhich hydrate was weighed?Karl FischerThe hydrate state and the mass balance

The manganese-to-assay ratio

The monohydrate is 32.5% manganese. The catalog pairs 31.5–33.0% manganese with an assay of at least 98.0%, and those figures fit: 31.9% manganese divided by 98.0% assay is 32.6%, the theoretical fraction. The anhydrous salt at the same assay gives 35.7 ÷ 98.0 = 36.4%. The ratio is a useful cross-check, but it is only valid when both figures share a basis.

Here is the trap. A monohydrate certificate can report manganese on a water-free basis: 35.7 ÷ 98.0 = 36.4%, the same ratio as the anhydrous salt. The water line settles it. A Karl Fischer result of 10.0–12.0% means the monohydrate; a result near zero means the anhydrous salt. A ratio below the theoretical figure suggests dilution, excess moisture or a manganese salt with a lower metal fraction. Use the ratio as a prompt for the next question, not as a release test.

X-ray diffraction and the solid state

XRD compares crystal lattices. The monohydrate and the anhydrous salt do not share a pattern, and the other hydrates have their own, so a reference pattern makes the form comparison direct. Colour and solubility are weaker evidence because both forms are pale and both dissolve.

XRD is not a routine release test here. A certificate that claims “XRD conforms” but omits the pattern and the reference has not shown much. Ask for the scan range, the reference and the detection limit. Thermogravimetry is a useful companion: it weighs the water as it leaves, and the size of the step separates a full monohydrate from a partly dried lot. On a disputed lot, XRD, water and titration together are stronger than any one alone.

What adulteration looks like

Substitutions to watch for and how they show
MaterialEffect on the lotSignalTest
Magnesium sulfateColourless filler; lowers manganeseManganese and assay low; magnesium highICP-OES, titration
Manganese chlorideSoluble and hygroscopicChloride high; water highIon chromatography, Karl Fischer
Manganese carbonateRaises manganese per gram; reacts with acidGas on acid; manganese high for the massAcid test, titration
Manganese dioxideBrown-black oxidiserColour; manganese high but insolubleXRD, titration
Ferrous sulfatePale green; similar lookIron high; manganese lowICP-OES
Sodium sulfateColourless diluentSodium high; manganese lowICP-OES
WaterDilutes the powderKarl Fischer high; as-is manganese lowKarl Fischer

Colour is the weakest signal. Pale pink covers a wide range, and a blend can reproduce it. The stronger signals are the manganese figure against the assay, the water result and the impurity panel. A certificate that reports appearance and assay but not water has left the most likely substitution untested.

Writing identity into the specification

  • “Manganese sulfate monohydrate, CAS 10034-96-5, MnSO4·H2O.”
  • “Assay ≥98.0% by complexometric titration; state the basis.”
  • “Manganese 31.5–33.0% by titration; state the basis.”
  • “Water 10.0–12.0% by Karl Fischer.”
  • “Identification by IR and titration, against a reference.”
  • “Particle size ≥95% through 40 mesh; metals and microbiology per the catalog.”
  • “No swap to the anhydrous salt or another manganese salt without written change control.”

Five questions for the supplier

  1. What hydrate is this lot, and what CAS number appears on the certificate?
  2. Are the assay and the manganese figure reported on the same basis, and what is that basis?
  3. What is the Karl Fischer water result, and does it sit inside 10.0–12.0%?
  4. Can you provide the IR spectrum and, if the hydrate is disputed, an XRD pattern against a reference?
  5. If a result is challenged, will you re-test the retained sample jointly with us?

Those five answers, taken together, form an identity file; one assay figure does not. The catalog specification is on the manganese sulfate product page; the COA page places each figure on the certificate; the grades page compares the forms; the level-four comparison covers the fill consequences; the methods notes explain the titration.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation