01 COA & batch testing

What the COA for manganese sulfate monohydrate actually contains

Technical document 01 · Reviewed 2026-11-19 · Manganese Sulfate

On this page
  1. How to read the certificate
  2. Why assay, manganese and water must agree
  3. Gate and result are different columns
  4. What changes from lot to lot
  5. When an outside laboratory is worth it
  6. Comparing two suppliers

A manganese sulfate monohydrate certificate is a release record for one lot: appearance, identity by IR and titration, assay, manganese, water, heavy metals, microbiology and particle size. The assay and the manganese figure only make sense together, because the water of crystallisation sits between them. The values in this table are the catalog gates; the lot certificate carries the measured results.

In one line

The assay and the manganese figure carry this certificate, with water beside them to show which hydrate was weighed.

How to read the certificate

A certificate becomes auditable when every line names the test, the method and the gate the lot had to pass. “Conforms” without a method is a conclusion, not evidence. Three lines decide what the powder is: identity says it is manganese sulfate, assay says how much monohydrate is present, and water says which hydrate was weighed. If one of the three is missing, the other two cannot carry the identification.

Release tests for manganese sulfate monohydrate
ParameterMethodRelease limit
AppearanceVisualPale pink, free-flowing powder
IdentificationIR and complexometric titrationConforms to the reference
AssayComplexometric titration≥98.0%
ManganeseComplexometric titration31.5–33.0%
WaterKarl Fischer10.0–12.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 40 mesh

Complexometric titration is the release method for both the assay and the manganese figure. It measures the metal directly, so the two results rise and fall together. IR adds the structural check: the sulfate bands and the water band show a hydrated sulfate rather than a different manganese salt.

Why assay, manganese and water must agree

Monohydrate means one water molecule per manganese ion. The pure salt is 32.5% manganese and 10.66% water; the specification brackets those values at 31.5–33.0% and 10.0–12.0%. At 98.0% assay the powder carries about 31.9% manganese as weighed. Recalculate that figure without the water and it becomes about 35.7%, close to the 36.4% of the anhydrous salt.

The three numbers are a single mass balance, not three independent opinions. A certificate that reports manganese near 36% on a monohydrate lot may be using a water-free basis; that is not proof of the anhydrous salt. The basis must be printed in the row. The assay needs its basis too, because a dried-basis figure and an as-received figure describe different quantities of powder. Water by Karl Fischer supplies the missing mass: it covers both the crystal water and any free moisture. With assay, manganese and water on one page, a reader can check the form; with assay alone, the reader cannot.

Gate and result are different columns

A specification value is a boundary. A batch value is a measurement. They should never share a cell. If the result column simply repeats the range, the certificate has not told the buyer what was found in the lot.

What the batch column should report
ParameterRelease limitBatch column
Assay≥98.0%Measured %, with method and basis
Manganese31.5–33.0%Measured %, with its own basis
Water10.0–12.0%Measured Karl Fischer %
Heavy metalsPer elementMeasured mg/kg per element
MicrobiologyCounts and absenceThe lot count and absence statement

Read manganese against water. A lot at 12.0% water holds less monohydrate per gram than a lot at 10.0%, so its manganese figure is lower and its fill weight higher. That is the specification working, not a failed batch. Heavy metals need one figure per element; a single total hides which metal is present.

What changes from lot to lot

Crystallisation and drying set the water result, and water is the most mobile line on the certificate. Colour moves within the pale pink range without any identity problem, but a brown cast is a different signal: it suggests oxidation, and the lot should be examined rather than accepted on appearance. The assay has less room to move; a lot close to 98.0% has little margin for another handling step. Particle size follows the mill and the sieve, so the 40 mesh result can change with no chemical change at all.

Look at the direction of travel across several lots, not one certificate at the edge. The lot code on the paper should also appear on the pouch, the drum and the retained sample.

When an outside laboratory is worth it

Use an outside laboratory for a new source, a first shipment to a regulated market, a disputed hydrate or a certificate that reports only conformity. A useful panel is titration for assay and manganese, Karl Fischer for water, IR for identity, ICP-MS for the metals, a plate count and a sieve check. If the hydrate is the question, add XRD or thermogravimetry: those tests see the crystal, while a second titration only repeats the metal result.

The report should give a detection limit for each screen, because “not detected” has no meaning without one. Keep the chain of custody intact and send the referee the retained sample, the certificate and the specification when a result is challenged.

Comparing two suppliers

Ask for the same six lines from each supplier: hydrate and CAS; assay and its basis; manganese and its basis; water; metals and microbiology; particle size and pack. A pair of certificates that agree on assay but disagree on water or basis does not describe the same powder. Then check traceability: who made the lot, how it was dried and milled, and whether the sample came from the pack being offered.

The catalog specification is on the manganese sulfate product page. The identity page sets out the tests that separate the hydrates, and the compliance page covers the market file. The methods notes describe the titration, and the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation