02.1 Monohydrate vs anhydrous

Manganese sulfate monohydrate vs anhydrous: the manganese figure and the fill

Technical document 02.1 · Reviewed 2026-11-19 · Manganese Sulfate

On this page
  1. Two forms, two identities
  2. The manganese figure per gram
  3. The fill weight follows the manganese
  4. Water, handling and the drift between the forms
  5. What the label has to say
  6. When to choose which

The monohydrate is 32.5% manganese by mass; the anhydrous salt is 36.4%. For the same declared manganese, the monohydrate needs about 12% more powder, and that difference lands in the fill weight, the capsule size and the blend. Both are manganese sulfate, but they are different specification items with different CAS numbers and different water figures. The manganese figure, read on the right basis, decides the fill.

In one line

The manganese figure decides the fill: the monohydrate carries 32.5% manganese and the anhydrous salt 36.4%, so the same label dose needs about 12% more monohydrate.

Two forms, two identities

Both materials are manganese(II) sulfate. The monohydrate, MnSO4·H2O, carries one water molecule per manganese ion and has CAS 10034-96-5; the anhydrous salt, MnSO4, has CAS 7785-87-7. The molecular weights are 169.01 and 151.00. The monohydrate is the stable form at ordinary temperature and humidity, and the anhydrous salt is hygroscopic: exposed to moist air it takes water back and moves toward the hydrate. That single behaviour explains most of the handling difference between them. The anhydrous salt therefore belongs in a sealed pack with a defined in-use period, not an open hopper.

Monohydrate and anhydrous manganese sulfate
PropertyMonohydrateAnhydrous
FormulaMnSO4·H2OMnSO4
CAS number10034-96-57785-87-7
Molecular weight169.01151.00
Manganese (theoretical)32.5%36.4%
Water10.66% boundEssentially none
HandlingStable; keep sealedHygroscopic; seal and use promptly
Label nameManganese sulfate monohydrateManganese sulfate, anhydrous

The manganese figure per gram

The manganese figure is the mass of manganese per mass of powder. For the monohydrate it is 54.94 ÷ 169.01 = 32.5%; for the anhydrous salt it is 54.94 ÷ 151.00 = 36.4%. The catalog monohydrate range is 31.5–33.0%, which brackets the theoretical value and allows for assay and water. The anhydrous salt has no catalog range on this page; if it is bought, it needs its own specification.

The basis is the trap. A monohydrate certificate can report manganese on the powder as received (about 32%) or on a water-free basis (about 36%). A figure near 36% therefore does not prove the anhydrous salt. Read the basis line and the water result before the form. This is the same distinction that makes certificates hard to compare between suppliers: two numbers that look different can describe the same lot. A monohydrate at 98.0% assay and 10.7% water is 31.9% manganese as-is and 35.7% on a water-free basis; the anhydrous salt at the same assay is 35.7% as-is. The two figures collide unless the water is on the page.

The fill weight follows the manganese

Start from the label declaration. If it is elemental manganese, divide by the manganese fraction of the form. A 10 mg declaration needs 10 ÷ 0.325 = 30.8 mg of pure monohydrate, or 31.4 mg at a 98.0% assay. The same declaration needs 27.5 mg of pure anhydrous salt, or 28.1 mg at 98.0%. The monohydrate is about 3.3 mg heavier per serving, 12% more. At 2 mg the difference is 0.7 mg; at 25 mg it is 8.2 mg. The factor applies to every declaration.

In a capsule the excipient absorbs the difference; in a tablet the compression weight may not, and in a stick pack the powder weight is visible on the label. If the declaration is the salt rather than the element, the fill is the declared salt weight and the manganese is the derived figure. Both directions are valid, but the label, the specification and the weigh-up have to use the same one. A 1 kg pack of monohydrate carries about 320 g of manganese at 32%, which is roughly 31,800 capsules at 10 mg before excipients; the same mass of anhydrous salt carries about 356 g and roughly 35,600 capsules. The pack size, not the salt name, sets how far a kilogram goes.

Water, handling and the drift between the forms

The monohydrate is specified at 10.0–12.0% water by Karl Fischer; the theoretical figure is 10.66%. That window is narrow on purpose. Above 12.0% the powder carries free moisture, which dilutes the manganese per gram and can cake. Below 10.0% the crystal has lost some of its water and is partly on the way to the anhydrous salt, which raises the manganese per gram. Either move changes the fill weight even when the assay is unchanged.

The anhydrous salt is the other extreme: it has no crystal water and takes it up readily. A drum that has been opened in a humid room can gain water in a short time, and the manganese figure falls as the mass rises. Keep both forms sealed, keep the drum liner closed, and record the opening date. A desiccant helps in a humid store but does not replace a seal. If the plant cannot guarantee dry handling, the monohydrate is the more forgiving purchase.

What the label has to say

The label has to name the form that was weighed. The EU list uses the spelling “manganese sulphate”; the label should still name the hydrate the material actually is. The nutrition declaration gives manganese in mg and as a percentage of the nutrient reference value, which is 2 mg/day for manganese in the EU. In the US, the Supplement Facts panel names the source in parentheses, for example “manganese (as manganese sulfate monohydrate)”, and the daily value for manganese is 2.3 mg. The declaration and the specification should use the same hydrate; a label that says monohydrate over an anhydrous lot is a mismatch even when the manganese figure is inside range.

The buyer's regulatory team confirms the wording and the route for the destination. This page is not a label approval, and it does not assert that either form is permitted in a given market.

When to choose which

Choose the monohydrate for supplements, for blends and for any plant that cannot guarantee a dry, sealed handling line. It is the stable ambient form, it is the form with the catalog specification, and its water figure is a built-in check on the hydrate. Choose the anhydrous salt only when the extra manganese per gram is worth the handling, for example in a concentrated premix or a formula where the crystal water is unwanted, and only with its own specification, its own water limit and a label that names it.

This is the form we supply: the monohydrate; the anhydrous salt is a separate purchase, not a substitution. For a different manganese salt, see the manganese gluconate and manganese bisglycinate pages. The grades page widens the comparison; the COA page shows how the results are reported; the identity page lists the tests that separate the hydrates; the product hub has the catalog specification.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation