Magnesium sulfate vs magnesium chloride: the anion, the solubility and the pack
Magnesium sulfate and magnesium chloride deliver different amounts of magnesium per gram, behave in opposite ways in a pack and put a different anion on the label. The sulfate is the heptahydrate, about 9.9% magnesium and efflorescent; the chloride is the hexahydrate, about 12.0% magnesium and deliquescent. For the same magnesium dose, the sulfate needs about 1.01 g per 100 mg against about 0.84 g for the chloride, so the choice changes the fill weight and the pack before it changes the assay.
The anion sets the magnesium per gram, the way the powder behaves in a pack and the name on the label; the two salts are not interchangeable at the same dose.
The anion is not a spectator
Both materials are magnesium salts, and both are sold as hydrates. The sulfate carries a divalent SO42− ion; the chloride carries two monovalent Cl− ions for every magnesium. That difference changes the formula weight, the mass of salt needed for a given magnesium dose, the taste, the osmotic load and the analytical test that proves the salt. It also changes the ingredient name on the label, which is a regulatory fact rather than a marketing choice.
The two hydrates have separate CAS numbers: magnesium sulfate heptahydrate, 10034-99-8, and magnesium chloride hexahydrate, 7791-18-6. A 12% magnesium figure on a certificate does not mean a stronger sulfate; it means the chloride or a blend. The hydrate and the anion have to be named together before any comparison is meaningful.
Magnesium per gram and the fill
| Property | Sulfate heptahydrate | Chloride hexahydrate |
|---|---|---|
| Formula | MgSO4·7H2O | MgCl2·6H2O |
| CAS number | 10034-99-8 | 7791-18-6 |
| Molecular weight | 246.47 | 203.30 |
| Magnesium | 9.86% (catalog 9.5–10.0%) | 11.95% (catalog 11.5–12.5%) |
| Water of crystallisation | 51.2% (catalog 48.0–52.0%) | 53.2% (catalog 45.0–55.0%) |
| Salt for 100 mg magnesium | 1.01 g | 0.84 g |
| Salt for 200 mg magnesium | 2.03 g | 1.67 g |
The arithmetic uses the theoretical magnesium content, not a batch result; the catalog ranges are wider and a real lot sits inside them. At 200 mg of magnesium, the sulfate needs about 0.36 g more salt than the chloride. That is enough to move a single-capsule dose into two capsules, or to turn a 1.7 g stick into a 2 g stick.
The hydrate matters as much as the anion. Anhydrous magnesium sulfate is 20.2% magnesium, and anhydrous magnesium chloride is 25.5%; comparing either anhydrous figure with the heptahydrate on the label would overstate the magnesium by a factor of two. The specification, the certificate and the label should all name the hydrate.
Solubility, solution and taste
Both salts are freely soluble in water, and at supplement-drink concentrations neither is limited by solubility. The sulfate heptahydrate dissolves at about 71 g per 100 mL at 20 °C; the chloride is the more soluble of the two and is deliquescent, so it can pull water from the air before it reaches the mixer. The practical difference is not whether the salt dissolves, but what the solution does afterwards.
The sulfate solution is close to neutral. The chloride solution is not identical in pH or taste, and the chloride puts three ions into solution per magnesium against two for the sulfate. At the same magnesium dose, that means a different osmotic load and a different mouthfeel. The sulfate reads as bitter and saline; the chloride reads as salty and bitter. Neither is neutral in a drink, and the formulator trials both at the real dose rather than at a rounded spoonful.
Calcium is the other solution question. A sulfate in a calcium-containing matrix can precipitate calcium sulfate, which shows up as haze, sediment or a loss of calcium in the finished product. The chloride does not remove calcium in the same way. If the formula carries calcium, the sulfate is the salt that needs the compatibility trial first.
Two packs, two failure modes
Both products are offered in a 1 kg foil pouch and a 25 kg fiber drum, so the pack list looks the same. The failure modes are opposite. Magnesium sulfate heptahydrate is efflorescent: warm, dry air pulls water out of the crystal, the water result falls below 48.0% and the magnesium percentage rises. Magnesium chloride hexahydrate is deliquescent: humid air is absorbed, the powder becomes damp and can cake or liquefy. A pack that protects one does not automatically protect the other in the same way.
The foil pouch is a barrier against both directions, which is why it is the standard pack for each. The difference appears after opening and in the drum liner. An open sulfate liner in a dry, warm store can lose water; an open chloride liner in a humid store can take water in. The in-use instruction, the liner and the storage condition should match the salt, not be copied from the other product.
Chloride also changes the equipment duty. A wet chloride solution is the harder environment for stainless-steel contact and can pit some grades; the sulfate solution is milder. That is a reason to check the wetted parts and the cleaning regime when switching, not a reason to accept a different salt without a specification change.
What the formula does with the difference
A capsule or tablet is a fill-weight problem. The sulfate needs more grams for the same magnesium, so the capsule count or the tablet weight rises. A stick pack is a mass and taste problem: a 2 g sulfate stick carries about 197 mg of magnesium, while 2 g of the chloride would carry about 239 mg. A drink is a taste, osmotic and compatibility problem: the chloride adds more ions and more chloride, while the sulfate can take calcium out of the matrix.
The label follows the salt. The ingredient list names magnesium sulfate or magnesium chloride, and the nutrition declaration states elemental magnesium. A formula switched from one salt to the other without recalculating the magnesium and rewriting the ingredient name is mislabelled even if the assay is correct.
When to choose which
Choose the sulfate when the product is a capsule, stick or drink that was formulated around the heptahydrate, when the pack can be kept sealed and dry, and when the calcium compatibility has been checked. Choose the chloride when the fill weight is the constraint, when the higher magnesium per gram justifies a new specification, and when the pack and the equipment can handle a deliquescent, chloride-bearing powder. The choice is a change control, not a purchase-order substitution.
Do not switch on the magnesium percentage alone. A 12% figure is not an upgrade if it changes the hydrate, the anion, the label, the taste and the pack. Rebuild the specification, the stability data and the label before the first order, and keep the two salts as separate line items.
The magnesium sulfate hub carries the heptahydrate specification; the magnesium chloride page carries the hexahydrate; the magnesium citrate page shows a third anion for comparison; the grade page covers the hydrate choice; the methods section covers the assays; the quality page covers the release file.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation