Anhydrous vs heptahydrate magnesium sulfate: water, magnesium and the label
Anhydrous magnesium sulfate and the heptahydrate are the same salt at two water contents. The anhydrous form carries about 20.2% magnesium and no more than 1% water; the heptahydrate carries about 9.9% magnesium and 48–52% water of crystallisation. For the same label dose the heptahydrate needs about twice the powder, and the label has to name the form that was weighed.
At about 20.2% magnesium against 9.9%, the anhydrous salt needs roughly half the powder for the same dose, and the water line is what separates the two forms.
The water line is the product line
The two forms are not a concentrate and a dilute version of one another. The heptahydrate is a crystal with seven water molecules built into its structure; the anhydrous salt is the same lattice with that water removed. The heptahydrate's water is stoichiometric, not a moisture allowance, so drying the crystal below 48.0% produces a lower hydrate rather than a stronger heptahydrate. The anhydrous salt is defined from the other side: its ≤1.0% loss on drying supports the name.
| Property | Anhydrous | Heptahydrate |
|---|---|---|
| Formula | MgSO4 | MgSO4·7H2O |
| CAS number | 7487-88-9 | 10034-99-8 |
| Molecular weight | 120.37 | 246.47 |
| Magnesium | 20.19% theoretical | 9.86% theoretical |
| Water | Loss on drying ≤1.0% | Water 48.0–52.0% |
| Behaviour in air | Hygroscopic; takes water in | Efflorescent; gives water up |
| Catalog form | 80 mesh powder | 40 mesh powder or crystals |
The analytical methods differ with the line. The anhydrous certificate reports loss on drying, while the heptahydrate certificate reports water by Karl Fischer against 48.0–52.0%. The two results are not interchangeable, and a certificate that says “water” without naming the method has left the form ambiguous.
Magnesium per gram and the conversion
The conversion factor is fixed by the formula: 246.47 ÷ 120.37 = 2.048. One gram of the anhydrous salt delivers the magnesium in about 2.05 g of the heptahydrate, and one gram of the heptahydrate delivers what about 0.49 g of the anhydrous salt would. The factor belongs to the formula, not the batch.
| Elemental magnesium | Anhydrous MgSO4 | Heptahydrate |
|---|---|---|
| 100 mg | About 495 mg | About 1,014 mg |
| 200 mg | About 990 mg | About 2,028 mg |
| 300 mg | About 1,486 mg | About 3,042 mg |
These figures use the theoretical content. A production lot at the catalog midpoint carries slightly less, so the label calculation should use the specification midpoint or the measured result rather than the theoretical maximum. The direction is what matters: the heptahydrate needs roughly double the mass for the same declared magnesium.
What the label has to say
The ingredient name and the magnesium declaration answer different questions. The ingredient list names the salt and its form; the nutrition panel declares elemental magnesium. A label that says “magnesium sulfate” without the form is ambiguous, because the same name covers the anhydrous salt and the heptahydrate. If the label says “anhydrous”, the certificate has to support that word.
The magnesium figure is also an audit tool. A 500 mg serving of “magnesium sulfate” that declares about 100 mg of magnesium is consistent with the anhydrous salt at roughly 20% magnesium. The same 500 mg of the heptahydrate would declare about 49 mg. A label that matches neither form has a formulation or naming problem, and no certificate repairs that.
In the EU, magnesium sulphate appears in Annex II to Directive 2002/46/EC as a permitted magnesium form for food supplements, and the label wording has to match the form in the file. In the US, the Supplement Facts panel declares the ingredient and the elemental magnesium. In both markets the claim review is separate: a magnesium claim is about the nutrient, not the sulfate.
The fill, the capsule count and the taste
The mass difference becomes a dosage-form decision. A 500 mg capsule of the anhydrous powder carries about 101 mg of magnesium; the same capsule of the heptahydrate carries about 49 mg. A 200 mg magnesium serving therefore needs two 500 mg anhydrous capsules, or about 2.03 g of the heptahydrate, which is four 500 mg capsules plus a remainder.
A stick pack shows the same arithmetic. A 1 g anhydrous stick carries about 202 mg of magnesium; a 1 g heptahydrate stick carries about 99 mg, so the heptahydrate formula usually moves to a 2 g stick for the same dose. The larger mass brings more powder to disperse, a stronger bitter and saline taste and a different osmotic load.
Dissolution adds a handling difference. The anhydrous salt hydrates as it dissolves and releases heat, so a concentrated stock warms up; the heptahydrate is already hydrated and does not carry that heat load. In a dry blend, the anhydrous powder can also take water from a hygroscopic partner.
The pack protects against opposite failures
Both products ship in a foil pouch and a lined fiber drum, but the failure modes are opposite. The anhydrous salt takes water in: a humid store, an open liner or a folded-over pouch moves the loss on drying above 1.0%, the magnesium figure falls on an as-is basis and the powder cakes. The heptahydrate gives water up: a warm, dry store can push the crystal below 48.0%, and the powder that remains is a lower hydrate.
A stability study follows the same split. For the anhydrous salt the humid arms at 30 °C/65% and 40 °C/75% relative humidity are the stress, and a dry arm is a control. For the heptahydrate the dry arm is the one that catches efflorescence. A pack that protects one form is not automatically the right pack for the other, even when the pouch looks identical.
In use, the anhydrous pouch is the more demanding. Once it is opened, the headspace holds room air and the surface starts to hydrate; a desiccant can help in a secondary container, but it does not replace a closed liner.
When to choose which form
Choose the anhydrous salt when the formula needs a low water content, when the fill weight is the constraint, or when the matrix is sensitive to added moisture. It is also the form to consider when the powder is expected to act as a desiccant in a dry blend, provided the formulator accepts the water and heat it brings.
Choose the heptahydrate when the formula, the label and the market file were built around it, when the larger mass per dose is acceptable and when the pack can keep the crystal inside its water range. It is not a weaker grade of the anhydrous salt; the two are separate specifications with separate certificates.
A switch in either direction needs a new specification, a stability check, a label review and a new COA. Do not substitute one for the other at the weigh-up and adjust the number afterwards. The anhydrous product hub carries this specification; the heptahydrate hub carries the other; the COA page shows how the drying result is reported; the grade page covers the particle choices; the methods section explains the assays; the quality page describes the release file.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation