06 Identity & adulteration

How to prove a magnesium oxide lot is the oxide

Technical document 06 · Reviewed 2026-11-19 · Magnesium Oxide

On this page
  1. The four identity layers
  2. The magnesium ratio: the first identity check
  3. X-ray diffraction and the solid-state form
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Six questions for the supplier

A magnesium oxide lot is the oxide when four lines agree: the document names MgO and CAS 1309-48-4, the identity test matches the reference, the magnesium figure is consistent with the assay, and the mass balance closes with the loss on drying and the acid-insoluble matter. The assay alone cannot separate the oxide from a hydroxide, a carbonate, a silicate or a dead-burned grade. The magnesium-to-assay ratio is the first check and needs no extra test.

In one line

Identity is the agreement of the magnesium figure with the assay, the IR or XRD pattern and the mass balance, not the word “magnesium oxide” on the certificate.

The four identity layers

A certificate can name the right material and still fail to prove it. The layers below are separate questions, and each needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.

Four layers of magnesium oxide identity
LayerQuestionTestWhat it proves
DocumentIs the material named?Name, CAS number, formula, sourcePaperwork only
SpectroscopyIs the solid the oxide?IR, or XRD for the crystalline patternThe chemical form, not the purity
Magnesium ratioDoes the magnesium match the assay?Complexometric titration or ICP-OESConsistency of the two figures
Mass balanceIs it diluted or altered?Loss on drying, loss on ignition, acid-insoluble matterConsistency of the whole sheet

The catalog identity line is “IR and titration conform”. That is a starting point. IR can show a carbonate or a hydroxide band, and titration supplies the magnesium figure, but neither one alone proves the solid-state form. XRD is the stronger check when the grade or the source is in dispute.

The magnesium ratio: the first identity check

Magnesium oxide is 60.3% magnesium by mass: 24.305 ÷ 40.304. A 96.0% MgO lot therefore carries 57.9% magnesium, and a 99.0% lot carries 59.7%. The catalog range of 57.0–60.0% magnesium brackets those figures. Multiply the assay by 0.603 and compare it with the reported magnesium; if the two differ by more than the method uncertainty, the certificate is using two different bases or the material is not pure oxide.

The ratio also flags the common alterations. Magnesium hydroxide is 41.7% magnesium, and magnesium carbonate is 28.8% on an anhydrous basis, so a hydroxide or carbonate layer lowers the magnesium figure rather than raising it. A lot that reports 60.0% magnesium with a 96.0% assay is not consistent on a single basis; it is more likely an as-is assay paired with an ignited-basis magnesium figure, and the basis question has to be settled before the lot is accepted.

The assay method matters for the same reason. Complexometric titration with EDTA measures the magnesium ion after the sample is dissolved; if the sample is ignited first, any hydroxide or carbonate is converted to oxide before the titration. The result is a true magnesium figure but not a true oxide figure. Pair the titration with loss on ignition and a carbonate check when the history of the lot is unknown.

X-ray diffraction and the solid-state form

X-ray diffraction answers the question the assay cannot: which crystalline phases are present? Magnesium oxide gives the periclase pattern. Magnesium hydroxide gives brucite, and magnesium carbonate gives magnesite or a hydrated carbonate pattern. A scan that shows only periclase is consistent with the oxide; extra peaks are a reason to ask what the lot contains, not a reason to reject on the first line.

Peak width adds a second piece of information. A light, precipitated oxide has small crystallites and broader peaks; a dead-burned oxide has larger crystallites and sharper peaks. The comparison is qualitative, but it separates a reactive grade from a refractory one when the supplier's description is vague. Ask for the reference pattern and the detection limit before reading a “match” statement; without them, the word “conforms” has no scale.

XRD is not a routine release test for magnesium oxide, and a certificate that reports only “XRD conforms” without the pattern has added little. It is most useful for a new source, a disputed grade, or a lot whose acid reaction does not match the certificate.

What adulteration looks like

Common magnesium oxide substitutions and the signals
Adulterant or changeWhat it doesSignalTest
Silica or talcRaises the acid-insoluble residue and dilutes the magnesiumAcid-insoluble above 0.1%; magnesium lowAcid-insoluble matter, XRD, ICP-OES for silicon
Calcium carbonate or dolomiteAdds calcium and carbonate; lowers the magnesium figureCalcium high; loss on ignition highICP-OES for calcium, FTIR, XRD
Hydroxide or carbonate layerForms on a wet or open lot; raises loss on ignitionLoss on drying or ignition high; acid reaction slowerLoss on ignition, FTIR, XRD
Dead-burned gradeSame formula, very low surface area and acid reactivityAssay passes; acid test slow; sharp XRD peaksAcid-consumption test, surface area, XRD
Another magnesium saltChloride or sulfate carries magnesium but not oxideConductivity high; chloride or sulfate detectedIon chromatography, conductivity

The list is not exhaustive, and a single signal is not proof. Silica raises the acid-insoluble figure but does not change the magnesium ratio much at a low level; a carbonate layer lowers the ratio and raises the ignition loss. Read the signals together, and ask for the test that separates the most likely substitution rather than a repeat of the assay.

How to write identity into the specification

  • “Magnesium oxide, CAS 1309-48-4, MgO, source and calcination route named.”
  • “Assay ≥96.0% as MgO by complexometric titration; magnesium 57.0–60.0%; state the basis.”
  • “Identification by IR and titration; XRD pattern on request for a new source or a disputed grade.”
  • “Loss on drying ≤0.5%; loss on ignition reported; acid-insoluble matter ≤0.1%.”
  • “Particle size ≥95% through 40 mesh; bulk density and acid-consumption check agreed on the qualification sample.”
  • “No hydroxide, carbonate or silicate above the agreed limit; no dead-burned material.”

Six questions for the supplier

  1. Which source and calcination route produced this lot, and which grade name is on the certificate?
  2. Is the assay calculated as-is, on the dried sample or on the ignited sample?
  3. What is the measured magnesium figure, and does it agree with the assay at a 0.603 ratio?
  4. What are the loss on drying, loss on ignition and acid-insoluble results for this lot?
  5. Can you provide the XRD pattern, or the IR spectrum, for a new source or a disputed grade?
  6. If the lot is disputed, will you accept a joint re-test on the retained sample?

Six direct answers amount to an identity file. A single assay percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grades page compares the source and calcination routes; the XRD method note explains the solid-state check; the EDTA titration note describes the assay; the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation