What the COA for magnesium oxide actually contains
A magnesium oxide batch certificate lists appearance, an IR and titration identity check, a complexometric assay, the elemental magnesium figure, loss on drying, acid-insoluble matter, the heavy-metal panel, microbiology and particle size. The document is useful only when every line shows the method, the release limit and the result obtained for that lot. The values below are the catalog limits; the COA is what ties them to a specific pack.
The assay and the magnesium figure are two views of the same powder, and the certificate is only complete when the basis, the acid-insoluble matter and the grade sit beside them.
What a batch certificate reports
Two things have to be visible on the page: which material was made, and what the laboratory found in the lot. The first is a matter of name, CAS number and identity test. The second is a set of measured values. A sheet that supplies one without the other cannot support a release decision.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | White powder |
| Identification | IR plus complexometric titration | Matches the reference |
| Assay (as MgO) | Complexometric titration | ≥96.0% |
| Magnesium (Mg) | Complexometric titration | 57.0–60.0% |
| Loss on drying | Gravimetric | ≤0.5% |
| Acid-insoluble matter | Acid digestion, filtration and ignition of the residue | ≤0.1% |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
| Particle size | Sieve analysis | ≥95% through 40 mesh |
Some lines carry more information than others. Assay and magnesium are two calculations from one measurement; moisture is a handling signal; acid-insoluble matter exposes silicate or ore residue that a purity figure would not show.
Assay, magnesium figure and the basis
The elemental figure is not an independent purity test. It is the assay restated as magnesium. In MgO the magnesium fraction is 24.305 ÷ 40.30 = 60.3%, so a 96.0% oxide contains 57.9% magnesium, which falls inside the catalog range of 57.0–60.0%. A certificate showing 96.0% assay beside 54.0% magnesium is either mixing two bases or carrying an error.
Ask which basis the assay uses: as received, dried or ignited. Ignition turns magnesium hydroxide and magnesium carbonate back into oxide before titration, so an ignited result describes the magnesium present and not the anion that was there. This is how a carbonated lot can satisfy an ignited assay while its as-is assay and ignition loss point elsewhere.
The moisture line needs the same care. The catalog limit is ≤0.5%, measured gravimetrically. That test drives off free water; it does not decompose hydroxide or carbonate, which release water and carbon dioxide at higher temperature. When a lot has been stored in a humid room or an opened container, request loss on ignition or a carbon dioxide determination as well. The drying result alone cannot answer the carbonation question.
Limit, result and the gap between them
A limit is the boundary for release; a result is what the bench measured. They need separate columns, and the method has to be named. Copying the specification range into the result column hides the very information the certificate exists to provide.
| Parameter | Release limit | Result column |
|---|---|---|
| Assay | ≥96.0% MgO | Measured percentage, with basis and titration method |
| Magnesium | 57.0–60.0% | Measured percentage, with the method used |
| Loss on drying | ≤0.5% | Measured percentage and drying condition |
| Acid-insoluble matter | ≤0.1% | Measured percentage, with the ignition step described |
| Heavy metals | Per element | Measured mg/kg for each element |
| Microbiology | Counts and absence | Count and absence statement for the lot |
| Particle size | ≥95% through 40 mesh | Measured percentage through the sieve |
“Passes specification” is a verdict, not evidence. A heavy-metal result belongs per element rather than as a sum; microbiology needs both a count and an absence statement; particle size needs the measured percentage through the sieve, not an adjective.
Where one lot differs from the next
Source and calcination are the first variables. A precipitated oxide, a ground oxide and a dead-burned oxide may all satisfy the magnesium figure while behaving unlike one another in a blend. Precipitation leaves a light, high-surface-area powder; grinding leaves a denser one; dead-burning leaves a low-surface-area material nearer to a refractory than to a supplement source. The certificate should identify the route, not just the formula.
Milling and sieving explain the particle-size result. Because 40 mesh is a finishing step, the number can move when the mill or the screen changes and the chemistry does not. Bulk density and flow never appear on the catalog sheet, yet they control how much powder goes into a capsule and whether a tablet press runs smoothly.
Storage and ore explain the other two lines. An opened bag in a damp room takes up water and carbon dioxide, so the as-is assay falls while an ignited result may stay put. A climbing acid-insoluble value points to silicate or ore residue. Neither shift shows up in a single assay percentage; they emerge when several lots are plotted together.
When a second laboratory earns its place
Independent testing makes sense for an unfamiliar source, a first shipment into a regulated market, a grade dispute, or a lot whose physical behaviour contradicts its certificate. The panel should answer the open question rather than duplicate the supplier's assay: XRD for periclase, brucite or magnesite; FTIR for carbonate and hydroxide; moisture and ignition loss on the same sample; acid-insoluble matter; ICP-MS for the metal panel; and ion chromatography for chloride or sulfate when a different magnesium compound is possible.
Every screen should come with its detection limit. A “not detected” entry without a limit says something about the method's reach, not about the sample. Traceability matters too: the material tested should be the material retained, and the report should name the lot and the pack.
For a disputed result, send the retained sample, the supplier's certificate and the specification to the referee, and ask for the tests that distinguish oxide from hydroxide, carbonate or silicate. Repeating the assay will not resolve a question about grade.
Six lines for a supplier comparison
Compare source and grade; assay and basis; magnesium figure; moisture and ignition loss; acid-insoluble matter with the metal panel; and particle size with bulk density. Quotations that match on assay but diverge on source or bulk density are not offers for the same powder.
Traceability is the second layer. The certificate should identify the manufacturer, the calcination route and the milling step, and its lot code should match the pouch, the drum and the retained sample. The catalog specification is on the magnesium oxide hub. The identity page covers the tests that separate oxide from carbonate or refractory material; the grades page explains the source choices; the EDTA titration note sets out the assay; the quality page describes the release file.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation