06 Identity & adulteration

How we prove a magnesium orotate lot is the dihydrate

Technical document 06 · Reviewed 2026-11-19 · Magnesium Orotate

On this page
  1. Four questions, four tests
  2. The 1:2 ratio and the mass balance
  3. X-ray diffraction and the solid-state check
  4. Routes of substitution
  5. Identity written into the specification
  6. Five questions to put in writing

A magnesium orotate lot is the dihydrate when four lines agree: the document names the hydrate and CAS 34717-03-8; HPLC and IR show the orotate; complexometric titration gives 6.4–6.8% magnesium; and Karl Fischer gives 9.0–11.0% water. The magnesium figure alone is the weakest line, because a blend of magnesium oxide and orotic acid can be built to the same percentage.

In one line

The magnesium assay can be imitated; the orotate by HPLC and IR, the 1:2 ratio and the water of crystallisation are what make the lot the salt.

Four questions, four tests

A certificate may name the right salt and still leave it unproven. The four layers ask separate questions and stand on separate tests. Answering only the first describes the paperwork, not the powder.

Four layers of magnesium orotate identity
LayerQuestionTestWhat it proves
DocumentIs the hydrate named?Name, CAS number, formulaPaperwork only
Organic partIs the anion orotate?HPLC retention with UV spectrum; IR against a referenceThe orotate molecule
Metal partIs the magnesium bound in the salt?Complexometric titration; ICP-OES as a checkThe magnesium content, not its source
Mass balanceIs it the dihydrate, or diluted?Karl Fischer water; assay and impuritiesConsistency of the numbers

No single layer is sufficient. HPLC can show orotic acid in a physical blend as readily as in the salt, and the titration can show magnesium from an oxide. The layers become evidence when they agree on the same lot.

The 1:2 ratio and the mass balance

The formula sets the targets. Magnesium orotate dihydrate is C10H6MgN4O8·2H2O at about 370.5 g/mol. Magnesium is 24.305 g/mol, or 6.56%; the two orotate anions account for about 84% of the mass as orotic acid equivalent; the two water molecules are 9.7%. A magnesium result inside 6.4–6.8% with water inside 9.0–11.0% is consistent with the dihydrate.

The salt is a 1:2 salt. One magnesium ion balances two orotate anions, so the molar ratio is fixed even though the mass ratio is not obvious. Convert both results to moles and the Mg : orotate ratio should sit near 1:2; a calculated ratio outside the agreed window points to free orotic acid, another magnesium source or a different hydrate. Because the ratio is calculated from two assays, its uncertainty combines both; put a range in the specification, not a single number.

Magnesium above 6.8% is a signal. The pure dihydrate cannot exceed 6.56% as-is, so a higher figure points to the anhydrous salt, a different hydrate, another magnesium source or an assay bias. A top-of-range figure is not a richer lot until water and identity explain it.

X-ray diffraction and the solid-state check

X-ray diffraction answers the solid-state question: is the powder crystalline, and does the pattern match a magnesium orotate dihydrate reference? It can separate a crystalline salt from an amorphous carrier or a blend, and it can compare lots from two sources. It is not a purity assay, and it does not measure the counter-ion.

The practical use here is the oxide screen. Crystalline magnesium oxide shows up in a diffraction pattern; how low it can be seen depends on the method and the preparation, so a “none detected” line needs the limit beside it. XRD is not a routine release test for this product; request it when a blend is suspected or a new source is being qualified. The XRD note explains the limit.

Infrared spectroscopy complements diffraction. Compare the spectrum with a dihydrate reference rather than orotic acid alone; the carboxylate and N–H regions separate a mixture from a reacted salt. The FTIR note describes the comparison.

Routes of substitution

Substitutions and the signals to test for
RouteWhat it doesSignalTest
Magnesium oxide plus orotic acidMatches the magnesium figure without forming the saltIR mismatch; water below the hydrate windowIR, XRD, Karl Fischer
Another magnesium saltRaises magnesium without adding orotateMagnesium high for the orotate resultHPLC, IR, ICP-OES
Free orotic acidLowers magnesium; adds an HPLC peakMagnesium low; orotic acid highHPLC related substances
Carrier or dilutionLowers assay and magnesium togetherBoth low; water and ash shiftMass balance, assay
WaterLowers as-is magnesium; dried basis normalKarl Fischer high for the lotKarl Fischer, assay basis

Colour proves the least: white to off-white covers a wide range, and a carrier can match it. The stronger signals are the HPLC orotate result, the magnesium figure, the water and the IR spectrum. Appearance and assay without an identity line leave the likely substitution untested.

Identity written into the specification

  • “Magnesium orotate dihydrate, CAS 34717-03-8, C10H6MgN4O8·2H2O.”
  • “Assay 98.0–102.0% by HPLC, with the basis stated.”
  • “Magnesium 6.4–6.8% by complexometric titration, with the basis stated.”
  • “Water 9.0–11.0% by Karl Fischer.”
  • “Identification by IR against a dihydrate reference and by HPLC retention with UV spectrum and peak purity.”
  • “No added magnesium oxide or another magnesium salt; related substances reported.”

The name is the first identity test. A specification that says “magnesium orotate” without the hydrate has already left the water and the magnesium basis open, and the certificate will follow the ambiguity.

Five questions to put in writing

  1. Which hydrate is this lot, and what are the Karl Fischer water and the magnesium result for it?
  2. Can you provide the HPLC chromatogram with the UV spectrum and the IR spectrum against a dihydrate reference?
  3. Was the magnesium result by titration or by ICP-OES, and on which basis is it reported?
  4. Was an XRD oxide screen run, and what limit of detection is reported?
  5. Would you accept a joint re-test of the retained sample if the lot is disputed?

Those five answers make an identity file; one assay percentage does not. Catalog data sits on the product hub; the COA page marks where each figure is reported; the grades page covers the salt choice; the HPLC note covers the separation; release control is described on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation