01 COA & batch testing

What the COA for magnesium lactate actually contains

Technical document 01 · Reviewed 2026-11-19 · Magnesium Lactate

On this page
  1. Reading the certificate as a test report
  2. Assay, magnesium and water share one arithmetic
  3. The limit column and the result column
  4. What changes between lots
  5. When an outside laboratory is worth it
  6. Comparing two suppliers

Magnesium lactate is released against a certificate that carries three connected figures: the lactate assay by titration, the elemental magnesium, and the water by Karl Fischer. The catalog specification is 98.0–102.0% assay, 8.5–9.5% magnesium and 18.0–22.0% water, with identification by IR and titration. A certificate that reports only the assay has not shown that the powder is the trihydrate.

In one line

The magnesium figure, the lactate assay and the water only mean something together: the certificate has to close the mass balance for a trihydrate.

Reading the certificate as a test report

A certificate line is only useful when it names the parameter, the method, and the limit the lot was released against. The method column is not decoration. Complexometric titration gives the magnesium figure, Karl Fischer gives the water, and IR plus a titration carries the identification. A “conforms” line without a method leaves the reader nothing to check.

The identity line matters because magnesium lactate is sold in more than one hydrate state. The assay line says how much lactate salt is present, the magnesium line says how much metal the powder carries, and the water line says how much of the mass is crystal water. Read together, the three lines describe one solid.

Release specification · magnesium lactate trihydrate
ParameterMethodRelease limit
AppearanceVisualWhite crystalline powder
IdentificationIR and titrationConforms to the reference
Assay (titration)Complexometric titration98.0–102.0%
Magnesium (elemental)Complexometric titration8.5–9.5%
WaterKarl Fischer18.0–22.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 40 mesh

Assay, magnesium and water share one arithmetic

The catalog ranges are 98.0–102.0% assay, 8.5–9.5% magnesium and 18.0–22.0% water, and they are not independent. The anhydrous salt C6H10MgO6 has a molecular weight of 202.44 and contains 12.01% magnesium by mass. Three water molecules, 54.05, take the trihydrate to 256.49 and 9.48% magnesium; the water is 21.07% of the crystal.

Take a powder with 20.0% water and an assay of 99.0% on the anhydrous basis. The dry matter is 80.0%, so the magnesium figure is 0.800 × 0.990 × 12.01% = 9.51%. Move the water to 18.0% and the same assay gives 9.75%, outside the magnesium range. Water and magnesium therefore move in opposite directions: a drier lot reports more metal per gram.

The certificate has to state the basis of the assay, because the arithmetic changes if the 98.0–102.0% is expressed on the trihydrate. In that convention the water is already inside the 100%, and a partly dried lot shows its extra magnesium through the water line rather than through the assay. Either way the three rows are one statement, and the buyer can check one against the others before release. Where the assay and the magnesium figure come from the same titration, they are one measurement stated twice, and the water row is the only independent check in the set.

The limit column and the result column

One column sets the acceptance boundary; the other records what the laboratory found. They belong in separate columns with the method beside them. If the result column repeats the range, there is no measurement to audit; “passes” is a conclusion, not a number.

What the result column should carry
ParameterRelease limitWhat the result column shows
Assay98.0–102.0%, with the basis namedA measured percentage and the basis used
Magnesium8.5–9.5%The measured elemental figure
Water18.0–22.0% by Karl FischerThe measured percentage
Heavy metalsPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kgA figure for each element
MicrobiologyCounts and absence testsThe counts and the absence statements
Particle size≥95% through 40 meshThe percentage through the sieve

Each metal gets its own figure; a combined total hides which element is present, and this specification is written per element. Microbiology is a count plus an absence statement. The absence of Salmonella applies to the portion tested, so the method and the portion size belong on the sheet.

What changes between lots

Crystallisation and drying set the water. A centrifuge that leaves more mother liquor, or a dryer that runs longer, moves the Karl Fischer result inside the 18.0–22.0% window and pulls the magnesium figure with it. The water line is the first place to look when the magnesium result sits near an edge.

Particle size follows the mill and the sieve. The catalog asks for ≥95% through 40 mesh; a change of mill can meet that line and still change how the powder flows on a capsule machine. Colour is a weaker signal: white crystalline powder is a narrow window here, and a grey or yellow cast is worth a question even when the assay passes.

One result near an edge tells you less than a trend across four lots. A slow fall in the lactate assay with stable water points at the titration or the standard; a fall that comes with rising water points at the dryer. Certificate, pouch, drum and retained sample should all carry one lot code.

When an outside laboratory is worth it

Reach for an outside laboratory when the source is new, the market is regulated and the shipment is the first, the hydrate is contested, or a certificate line says only “conforms”. The panel is narrow: complexometric titration for magnesium, Karl Fischer for water, IR for identity, lactate by HPLC for the counter-ion, ICP-MS for the listed heavy metals, and the microbiology set.

If the hydrate is the dispute, add X-ray diffraction against a reference pattern. If the label claim for elemental magnesium is being set, ask for the magnesium and water results from the same lot so that the as-is figure can be calculated. The laboratory should report its detection limit for each contaminant, because a result without a limit cannot be compared with the release gate.

Chain of custody is part of the test. Send the retained sample for testing, and require the report to identify the lot. A contested result needs the retained sample, the certificate and the specification in the referee's hands, plus a request for the test that discriminates between the two explanations, not another run of the same titration.

Comparing two suppliers

Six lines make a comparison: the hydrate state and CAS number; the assay with its basis; the magnesium figure; the water; the contaminant and microbiology results; the pack size and lot code. Two quotations that agree on assay but differ on water are not offering the same powder, and the magnesium figure will show it.

The second layer is traceability: who made the lot, which crystallisation and drying route was used, and which mill set the particle size. Catalog ranges are on the magnesium lactate product page. The tests that separate the hydrate states are on the identity page; market files are on the compliance page; the titration is described in the complexometric titration note; the release procedure is set out on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation