06 Identity & adulteration

How we prove a magnesium lactate lot is the trihydrate

Technical document 06 · Reviewed 2026-11-19 · Magnesium Lactate

On this page
  1. The five identity layers
  2. One magnesium for every two lactate ions
  3. X-ray diffraction and the crystal form
  4. How substitution shows up
  5. Writing identity into the specification
  6. Five questions to put to the supplier

A magnesium lactate lot is the trihydrate when five measurements agree: the document names the hydrate and the CAS number, IR matches the reference, the magnesium titration is 8.5–9.5%, the lactate figure is about 69%, and the water is 18.0–22.0%. The assay alone cannot tell the trihydrate from the anhydrous salt, a magnesium oxide blend or a sulfate blend. The magnesium-to-lactate ratio and the water close the mass balance.

In one line

Identity is the agreement of the magnesium figure, the lactate figure and the water: one magnesium for every two lactate ions, with the trihydrate's water in the balance.

The five identity layers

A certificate can carry the right name and still fail to prove the powder. Each layer asks a different question and needs its own evidence. An answer to the first alone describes the paperwork, not the powder.

Five layers of magnesium lactate identity
LayerThe questionMethodWhat it establishes
DocumentIs the hydrate named?Name, CAS number, formulaPaperwork only
InfraredIs the salt magnesium lactate?IR against a reference spectrumThe salt family
MagnesiumHow much metal is present?Complexometric titrationThe elemental figure
LactateIs the counter-ion lactate, and in the right ratio?HPLCThe anion and the stoichiometry
WaterIs it the trihydrate?Karl FischerThe hydrate state

The order matters. The document layer can be corrected with a new certificate; the analytical layers cannot. If the IR matches and the magnesium is in range but the water is 2%, the powder is the anhydrous salt or a partly dried lot, and the name on the certificate is the thing that is wrong.

One magnesium for every two lactate ions

The salt is one magnesium ion and two lactate ions. The theoretical magnesium figure for the trihydrate is 9.48%, and the lactate figure that goes with it is 69.45%; the remaining 21.07% is water. The mass ratio of lactate to magnesium is about 7.3, and the molar ratio is 2.0. Both ratios hold for the anhydrous salt as well, because removing water does not change the salt: the anhydrous solid is 12.01% magnesium and 88.0% lactate, and its ratio is still 7.3.

That makes the ratio a check on the salt, not on the hydrate. A powder with 9.5% magnesium and 60% lactate has too little anion for the metal, so part of the magnesium is not bound to lactate. A powder with 9.5% magnesium, 69% lactate and 10% water has the right salt but too little water for the trihydrate. A powder with 12% magnesium, 88% lactate and 0% water is the anhydrous salt, correctly described. The three figures together say which solid is in the bag.

Work the arithmetic before accepting a “magnesium lactate” certificate. Divide the magnesium percentage by 24.305 to get moles of metal per 100 g: 9.48 ÷ 24.305 = 0.390. Multiply by two and by 89.07 to get grams of lactate per 100 g, 69.5 g, and add the water percentage. The total should land close to 100% for a pure salt. A total well below 100% means a filler or a second salt; a total above 100% means one of the three figures is wrong.

X-ray diffraction and the crystal form

XRD asks whether the solid is the crystalline trihydrate and whether the pattern matches a reference. It separates the trihydrate from the anhydrous salt and from an amorphous blend, and it can show a partly dried lot that contains both patterns. XRD is neither a purity assay nor a counter-ion measurement.

This is not a routine release test. Order it when the hydrate is contested, when qualifying a new source, or when the water sits at the edge of the range and the magnesium is ambiguous. Before accepting a “match” statement, require the reference pattern and the limit of detection; a bare “XRD conforms” line proves little. On a contested lot, combine XRD, Karl Fischer and the two assay figures rather than relying on one.

How substitution shows up

Common substitutions in magnesium lactate and what they leave behind
SubstituteEffectClueCheck
Anhydrous saltRaises magnesium; removes waterMg above 9.5%; water below 18%Karl Fischer, XRD
Magnesium oxideHigh magnesium; no lactate; alkalineMg high; lactate low; cloudy solutionTitration, HPLC, pH
Magnesium sulfateMagnesium close to the lactate figure; no lactateSulfate present; lactate lowSulfate test, HPLC, IR
Magnesium citrateHigher magnesium; citrate presentCitrate by HPLC; different solubilityHPLC, IR
MaltodextrinDilutes every figureLow Mg and low lactate; high dry matterMass balance, HPLC

The sulfate row is the one that surprises buyers. Magnesium sulfate heptahydrate carries 9.9% magnesium, close enough to the 9.5% of the trihydrate that a magnesium-only specification will not separate them. The lactate figure and a sulfate test will. Appearance tells you least: a white powder is easy to imitate, and a blend can look right while the ratios are wrong.

Writing identity into the specification

  • “Magnesium lactate trihydrate, CAS 18917-93-6, C6H10MgO6·3H2O.”
  • “Assay 98.0–102.0% by complexometric titration; the basis is stated on the certificate.”
  • “Magnesium 8.5–9.5%; water 18.0–22.0% by Karl Fischer.”
  • “Identification by IR against a reference spectrum and by titration.”
  • “Lactate by HPLC; report the figure so the magnesium-to-lactate ratio can be checked.”
  • “Particle size ≥95% through 40 mesh; contaminants and microbiology per the certificate.”

Five questions to put to the supplier

  1. What hydrate is this lot, and what CAS number appears on its certificate?
  2. What are the magnesium, lactate and water results for the lot, and do they close the mass balance?
  3. Will you release the IR spectrum and the HPLC chromatogram alongside the assay figure?
  4. What is the water by Karl Fischer, and was the assay reported on the anhydrous or the trihydrate basis?
  5. If the hydrate is contested, will you join a re-test on the retained sample, with XRD included?

Five straight answers make an identity file; a single assay figure does not. Catalog ranges are on the product hub; the certificate layout is on the COA page; the hydrate comparison is on the grades page; the salt comparison is on the lactate versus citrate page; the solid-state methods are described in the FTIR note and the XRD note.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation