Magnesium lactate trihydrate or anhydrous: choosing a grade
Magnesium lactate is supplied as the trihydrate, as the anhydrous salt, and as a granulated powder for flow. The trihydrate is the catalog form: C6H10MgO6·3H2O, 256.49 g/mol, 9.48% magnesium and 21.07% water. The anhydrous salt carries 12.01% magnesium, so the same label claim needs about a fifth less powder.
The hydrate is a mass decision: the trihydrate carries about 9.5% magnesium against about 12.0% for the anhydrous salt, so the same claim needs more powder.
Why the hydrate comes first
Magnesium lactate is one magnesium ion and two lactate ions. In the trihydrate, three water molecules sit in the crystal as well, and they are part of the solid rather than a drying fault. The commercial powder is normally this crystal because it is the form that crystallises cleanly and keeps its water at ambient conditions.
The anhydrous salt is the same lattice without the water, made by drying the hydrate. It is a legitimate material with its own specification, and it is hygroscopic: left open in a humid room it takes water back and moves toward the hydrate. Granulation is a physical step applied to either solid; it changes the particle size and the flow, not the hydrate.
CAS 18917-93-6 is the number quoted here for the trihydrate. A purchase order that says only “magnesium lactate” has not named the solid, and the certificate cannot settle the question after the fact if the specification never asked it.
The two hydrates side by side
| Property | Trihydrate | Anhydrous |
|---|---|---|
| Formula | C6H10MgO6·3H2O | C6H10MgO6 |
| Molecular weight | 256.49 | 202.44 |
| Magnesium | 9.48% | 12.01% |
| Water | 21.07% in the crystal | None in the formula |
| Powder for 100 mg magnesium | About 1,055 mg | About 833 mg |
| Magnesium in a 500 mg fill | About 47 mg | About 60 mg |
| Water solubility | Freely soluble | Freely soluble |
| Handling | Stable crystal; keep sealed | Takes water from humid air; reseal |
The 18.0–22.0% water range in the catalog belongs to the trihydrate. A lot at 21% water and 9.5% magnesium is a normal trihydrate, not a wet lot. An anhydrous grade would be specified with a low water limit and a magnesium figure near 12%, and it should never be accepted against the trihydrate specification merely because the assay is higher.
Water, flow and the mill
The catalog form is a white crystalline powder at ≥95% through 40 mesh. Granulation makes a coarser, denser particle that flows more evenly and raises less dust, and it is quoted as a separate item because the particle-size line moves. The magnesium figure does not move with granulation; if a supplier offers a granulated grade with a different assay, that is a new specification rather than a packing option.
Both hydrates are freely soluble in water, and the lactate solution is close to neutral. That is why the salt suits sticks, drink mixes and any format where the powder has to disappear into water. The difference is in the powder room: the anhydrous grade pulls moisture from the air, so an open liner, a humid filling room or a long hold in a hopper all work against it.
Caking is the practical failure. A trihydrate stored at the dry end of its water range can lose surface water and cake at the bag seams; an anhydrous grade stored humid can gain water and cake throughout. The fix is the pack and the room, not a different hydrate. Ask for the water result on the lot and keep the liner closed between uses.
The dose arithmetic
The label declares elemental magnesium; the powder mass is the carrier. Divide the claimed magnesium by the magnesium fraction of the grade. At 9.5%, a 100 mg claim needs 1,053 mg of trihydrate; at the bottom of the range, 8.5%, it needs 1,176 mg. The same claim on the anhydrous salt at 12.0% needs 833 mg.
Per capsule, the difference is visible. A 500 mg fill of trihydrate delivers about 47 mg of magnesium, while the same fill of anhydrous salt delivers about 60 mg. A 100 mg claim needs about 833 mg of the anhydrous salt or 1,055 mg of the trihydrate, so whether it fits one capsule depends on the bulk density; the trihydrate more often needs two capsules or a stick. A 200 mg claim is 2,105 mg of trihydrate, which is a stick pack or a tablet rather than a single capsule.
These figures are planning arithmetic from the formula, not a release result. The lot certificate, not the catalog midpoint, is what the capsule machine or the press should be set against: a low-magnesium lot needs a heavier fill. The calculation is the same one that decides the fill weight, and the fill weight is what the label claim has to survive.
What to write into the specification
- “Magnesium lactate trihydrate, CAS 18917-93-6, C6H10MgO6·3H2O.”
- “Assay 98.0–102.0% by complexometric titration; the basis is stated on the certificate.”
- “Magnesium 8.5–9.5%; water 18.0–22.0% by Karl Fischer.”
- “Identification by IR and titration; appearance white crystalline powder.”
- “Particle size ≥95% through 40 mesh; granulated grade quoted with its mesh and bulk density.”
- “Heavy metals and microbiology as listed; lot code on the pack and the certificate.”
When the other grade is wrong
Do not switch an approved trihydrate formula to the anhydrous salt without recalculating the dose. The label claim stays the same, the powder mass falls, and the capsule size or the tablet weight may fall with it; that is a change control, not a purchasing convenience. The reverse switch is worse: a formula built on 833 mg of anhydrous salt cannot absorb 1,055 mg of trihydrate without a bigger capsule.
Do not read the trihydrate's 21% water as a quality defect. It is the crystal. A specification that asks for “low water” on a trihydrate is asking for a different solid, and a supplier who meets it has either dried the hydrate or supplied the anhydrous salt.
Granulation is the right answer when flow or dust is the problem, and the wrong answer when the magnesium figure is the problem. The product hub carries the catalog ranges; the COA page shows where water and magnesium sit on the certificate; the lactate versus citrate comparison takes the salt choice further; the stability page covers what the powder does in the pack; the hydrate glossary entry defines the term.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation