01 COA & batch testing

What the COA for magnesium L-threonate actually contains

Technical document 01 · Reviewed 2026-11-18 · Magnesium L-Threonate

On this page
  1. The one-page sheet
  2. What 98.0–102.0% is measured against
  3. Where the limit ends and the result begins
  4. What moves between lots
  5. When a second laboratory earns its fee
  6. Six lines to compare between suppliers

A certificate for magnesium L-threonate reports two potency figures, not one: the salt assay at 98.0–102.0% on the dried basis and the elemental magnesium at 7.2–8.3%. Around them sit the identity tests, pH, loss on drying, particle size and the contaminant panel. Every lot is released against the same frame, and the batch COA carries the result for that lot.

In one line

Two percentages share one certificate: the salt assay describes the molecule, the magnesium figure describes the element, and neither one establishes the L form.

The one-page sheet

The certificate is a release record rather than a catalogue. Each parameter is paired with a method, a limit and a result. A number with no method cannot be audited; a limit with no result is only an intention.

Batch COA frame · magnesium L-threonate, catalog release limits
ParameterMethodRelease limitReported as
AppearanceVisualWhite to off-white crystalline powderResult
IdentificationIR and L-threonate reactionConforms to referenceResult
Magnesium L-threonate, saltTitration, dried basis98.0–102.0%Result
Magnesium (Mg)Titration7.2–8.3%Result
pH, 5% solutionPotentiometry5.8–9.0Result
Loss on dryingGravimetric≤5.0%Result
Particle sizeSieve analysis≥95% through 80 meshResult
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kgResult
MicrobiologyPlate count and enrichmentAPC ≤1,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli and Salmonella absentResult

Microbiology is a second block on the same page. The limits are written into the specification before the lot is made.

What 98.0–102.0% is measured against

The salt assay answers how much magnesium L-threonate the sample contains. The magnesium figure answers how much of the element is present. The two are related by the formula, and they are not interchangeable.

Anhydrous magnesium L-threonate has the formula C₈H₁₄MgO₁₀ and a molar mass of about 294.5 g/mol. Magnesium accounts for 24.3 g/mol of that total, or 8.25%. A salt assay of 100% therefore corresponds to about 8.25% magnesium; 98.0% corresponds to about 8.09% and 102.0% to about 8.42%. The catalog magnesium range of 7.2–8.3% brackets that figure, with room for hydrate variation and method uncertainty.

“Dried basis” is the second part of the definition. If loss on drying is 5.0% and the dried-basis salt assay is 98.0%, the material as weighed contains about 93.1% salt. The water has been removed from the denominator, not from the drum. The certificate should say which basis each result uses; the loss-on-drying line allows the conversion.

The ligand supplies a third view. Magnesium L-threonate is roughly 92% L-threonic acid by mass, so a 98% salt assay corresponds to about 90% acid. The EU novel-food specification describes the material by an L-threonic acid content of not less than 85% and magnesium at 7.2–8.3%. Both frames can describe the same lot, but the market file asks for its own figure.

Where the limit ends and the result begins

A release limit is a gate. A batch result is a measurement. The batch COA confirms the lot against the limits, and the result belongs beside the limit, the method and the basis. “Conforms” on its own is a conclusion without the evidence; it is acceptable for a pass/fail attribute such as appearance or identification, not for an assay.

The contaminant lines deserve the same discipline. A lead limit of 3 mg/kg is also the EU ceiling for a food supplement, so a lot released at the limit leaves no margin for the rest of the formula; a tighter purchase limit is the buyer’s choice. The arsenic figure of 2 mg/kg is a buyer-set limit, because the EU has no harmonised arsenic maximum for food supplements.

Microbiology is reported as counts and as absence. The absence of E. coli and Salmonella is a qualitative result; the aerobic plate count is a number. Both belong on the certificate with the method named.

What moves between lots

The salt assay tracks crystallisation and drying, and the magnesium figure moves with it. A lot with a high salt assay and a low magnesium figure deserves a check of the hydrate state and the calculation before an adulterant is suspected. Water content reflects the drying stage and the water held in the crystal; pH reflects the acidity left by the crystallisation liquor; mesh reflects milling and sieving.

Because the magnesium content is only about 8%, a small absolute change is a larger relative change. A shift of 0.1 percentage points is about 1.2% of the magnesium figure. That is why the magnesium method needs good repeatability, and why one decimal place matters more here than on a 14% salt.

Colour is the weakest quantitative signal here, and often the one that starts the most useful conversation. A cream or tan cast can follow an overheated dryer or a trace of iron. The assay may still pass. Ask for the batch record instead of rejecting the lot on sight.

When a second laboratory earns its fee

Outside testing earns its place at three moments: a new source, a first shipment into a regulated market, or a label claim that the certificate does not actually support. There is no value in duplicating every line. Pick the few tests that close the gap the supplier’s data leaves open.

For this salt that usually means an independent titration for the salt and for magnesium, ICP-MS for the contaminant panel, an L-threonic acid assay by ion chromatography or LC-MS, specific rotation for the L form, and IR for the fingerprint. X-ray diffraction can add a screen for crystalline magnesium oxide if a blend is suspected. The titration method note explains what a complexometric result does and does not prove.

A second laboratory is also the neutral ground for a disagreement: put the retained sample, the supplier’s COA and the agreed specification in front of it, and ask which tests discriminate the form rather than for a repeat of the whole panel.

Six lines to compare between suppliers

  • The salt assay, its method and its basis: dried or as-is.
  • The magnesium figure and the method beside it.
  • The identity package: IR, L-threonate reaction, L-threonic acid and specific rotation.
  • Loss on drying and the hydrate state named on the certificate.
  • pH, particle size and the mesh fraction actually measured.
  • Heavy metals, microbiology and the batch record behind the lot number.

Two quotations that match on the salt assay but diverge on the other five lines describe different materials, whatever the heading on the offer. The identifier should be identical on the certificate, the pouch and the retained sample; if one of the three differs, the traceability chain is broken.

The catalog specification sits on the magnesium L-threonate product page. The identity page sets out the tests that distinguish the L salt from a blend, the grade page compares the salts, and the quality page describes how a lot is released.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation