02.1 Anhydrous vs nonahydrate

Anhydrous vs nonahydrate magnesium citrate: the fill-weight question

Technical document 02.1 · Reviewed 2026-11-18 · Magnesium Citrate

On this page
  1. One salt, two solids
  2. The arithmetic per dose
  3. What the water does
  4. The fill weight in practice
  5. Flow, density and processing
  6. What has to change on the label
  7. Choosing between them

The two grades differ by water and nothing else chemically: the anhydrous salt is Mg₃(C₆H₅O₇)₂ at about 451 g/mol and 16.2% magnesium, while the nonahydrate carries nine water molecules, about 613 g/mol and 11.9% magnesium. For the same label claim the hydrate needs roughly a third more powder, and that difference lands on the capsule size, the tablet weight or the stick-pack fill.

In one line

The nonahydrate carries about 11.9% magnesium against about 16.2% for the anhydrous salt, so switching grade moves the capsule fill weight by roughly a third.

One salt, two solids

Magnesium citrate is the salt formed when three magnesium ions balance two trivalent citrate ions. The anhydrous grade is that lattice on its own, quoted under CAS 3344-18-1. The nonahydrate is the same lattice with nine water molecules built into it, and it is normally quoted under its own CAS number and its own specification — confirm which number your purchase order cites, because the two documents describe different solids.

Neither form is more “pure” than the other. The nonahydrate is a fully formed crystal that happens to contain water; the anhydrous salt is the same crystal without it. A certificate showing 11.9% magnesium is not describing a weaker material; it is describing a heavier molecule.

The arithmetic per dose

The calculation is a division. Take the elemental dose the label claims and divide by the magnesium fraction of the grade: 16.2% for the anhydrous salt and 11.9% for the nonahydrate. The result is the mass of powder the formula has to carry.

Powder mass needed for a magnesium dose, by grade
Elemental magnesiumAnhydrous salt, 16.2%Nonahydrate, 11.9%Extra mass
50 mgabout 309 mgabout 420 mgabout 111 mg
100 mgabout 617 mgabout 840 mgabout 223 mg
150 mgabout 926 mgabout 1,261 mgabout 335 mg
200 mgabout 1,235 mgabout 1,681 mgabout 446 mg

The percentages are calculated from the formula, so read the table as a planning figure rather than a fill-weight release. A lot at the bottom of a magnesium range needs more powder than a lot at the top, and the certificate for the lot is what the press or the capsule machine should be set against.

What the water does

Nine water molecules weigh about 162 g/mol, which is 26.4% of the nonahydrate. That single number explains the loss-on-drying line. The anhydrous grade is specified at ≤2.0% because it has almost no lattice water to lose; the nonahydrate will report around 26% and that is the correct result for the grade, not a wet lot.

It also means a nonahydrate cannot be accepted against an anhydrous specification. The drying limit is not a tolerance that a hydrate can be argued into; it is a different measurement of a different solid. When the hydrate is the disputed point, Karl Fischer water is the more direct test, because loss on drying at 105 °C can leave part of the water behind in some crystal forms.

Water also changes the powder's behaviour before it reaches the press. The anhydrous salt has a stronger drive to take up moisture from the air because it can move toward a hydrate; the nonahydrate is already there. Both cake if they are stored wet, but the anhydrous grade is the one that changes weight and flow in an open liner.

The fill weight in practice

A 500 mg capsule fill delivers about 81 mg of magnesium from the anhydrous salt and about 60 mg from the nonahydrate. A label claim of 100 mg elemental magnesium therefore needs a larger capsule, a second capsule, or a denser fill on the hydrate, and that is the decision the capsule-count calculation is really about.

Capsule geometry sets a ceiling. A size 00 capsule takes about 0.95 mL, so at 0.65 g/mL it holds roughly 600 mg of this powder — about 97 mg of magnesium from the anhydrous salt and about 71 mg from the nonahydrate at the same density. One capsule per dose is realistic on the anhydrous grade; on the hydrate it usually is not.

Tablets have the same constraint in a different shape. A 1,000 mg tablet weight is a large tablet for most consumers, so a 100 mg claim on the nonahydrate is already at 840 mg of active powder before any excipient. Stick packs and sachets are more forgiving of mass, which is one reason the hydrate is common in those formats.

Flow, density and processing

The anhydrous grade specified here is a 40 mesh powder with a bulk density of 0.50–0.80 g/mL, and that range is wide enough that two lots can feel like two materials on the same press. For the nonahydrate, ask for the bulk density and the mesh on the certificate for the lot rather than assuming they match. Crystal habit and drying route move those figures more than the hydrate name does.

If flow is the problem, granulation is usually a better answer than a change of hydrate. Granulating the anhydrous salt gives a denser, more uniform particle without giving up the magnesium per gram, whereas switching to the nonahydrate buys flow but needs a third more mass per dose.

What has to change on the label

In the European Union, the ingredient list names the magnesium source and the nutrition declaration reports magnesium in milligrams and as a percentage of the 375 mg reference intake. In the United States, the Supplement Facts panel states the elemental magnesium figure against a 420 mg Daily Value, and the ingredient list names the salt. In both markets the salt name is the same word, which is precisely why the declaration matters: the consumer cannot see the hydrate from the ingredient list.

If the label quantifies the ingredient, the figure has to be recalculated when the grade changes. A product declaring 1,000 mg of magnesium citrate provides about 162 mg of magnesium on the anhydrous grade and about 119 mg on the nonahydrate. Keeping the old declaration after a silent grade change is a labelling error that no certificate will catch.

The hydrate belongs in the specification, the technical data sheet and the certificate, where the buyer and the auditor will look for it. The compliance page sets out the label rules in full.

Choosing between them

  • Choose the anhydrous salt when the capsule size or the tablet weight is fixed, the dose is high, and the label is already approved.
  • Choose the nonahydrate when the format is a stick, a beverage or a gummy, where mass is available and the hydrate disperses readily.
  • Choose neither on the drum weight alone; compare the mass needed per dose.
  • Run a grade change as a change control: new specification, new stability data, new label arithmetic.

The grade comparison places both forms among the milled and granulated variants, the COA page shows where the hydrate is declared, and the stability page covers what each grade does in the matrix.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation