02 Grade comparison

Anhydrous or nonahydrate: choosing a magnesium citrate grade

Technical document 02 · Reviewed 2026-11-18 · Magnesium Citrate

On this page
  1. The hydrate is part of the identity
  2. The two grades side by side
  3. What the drum carries
  4. What changes in the finished product
  5. How to write the specification
  6. When not to switch

Magnesium citrate is sold as the anhydrous salt and as the nonahydrate, and the two are the same anion carrying different amounts of water. The anhydrous grade carries 14.5–16.4% magnesium and is the grade specified on this site; the nonahydrate carries about 11.9% and is quoted against its own specification. The choice between them is a fill-weight and label decision before it is a quality decision.

In one line

The two grades are the same salt with different water; the choice is a fill-weight and label decision, not a purity one.

The hydrate is part of the identity

Water of crystallisation is not surface moisture that a dryer can remove at will. It is built into the crystal lattice, it changes the molar mass, and it therefore changes how much magnesium a kilogram of powder contains. Anhydrous magnesium citrate is Mg₃(C₆H₅O₇)₂ at about 451 g/mol. The nonahydrate is the same formula plus nine water molecules, about 613 g/mol, and the water is roughly 26% of the mass.

A purchase order that says “magnesium citrate” has therefore named a family, not a material. Two drums that answer to that name can differ by a third in the mass needed for the same label claim. The hydrate belongs in the specification, in the technical data sheet and on the certificate, because it decides the arithmetic that follows.

The two grades side by side

Magnesium citrate grades · what changes between them
GradeWaterElemental MgLoss on dryingFitsWatch
Anhydrous, 40 meshNone in the lattice14.5–16.4% (EDTA)≤2.0%Capsules, tablets, high-dose powdersGreater drive to take up water
NonahydrateNine molecules, about 26%About 11.9%About 26%, against its own limitSticks, beverages, gummiesAbout a third more mass per milligram
Milled, 80 meshAs the base gradeAs the base gradeAs the base gradeCapsules, suspensionsDust, flow, blend segregation
GranulatedAs the base gradeAs the base gradeAs the base gradeTablets, sachetsGranulation aids must be declared

The last two rows are process variants, not different chemistry. Milling and granulation change particle size, bulk density and dust; they do not change the magnesium figure, and they should not be used to explain one.

What the drum carries

The anhydrous grade specified here is a 40 mesh powder: at least 95% passes a 425 µm sieve, and bulk density runs at 0.50–0.80 g/mL. That range is wide enough to feel like two materials. A lot at the dense end fills a capsule or a tablet die with more mass per stroke than a lot at the light end, and a formulator who qualified on one end will notice the other.

Flow and caking follow moisture more than they follow the hydrate label. The anhydrous salt has a stronger driving force to pick up water from the air, because it can move toward a hydrate; the nonahydrate begins with its water already in place. That does not make the nonahydrate immune to caking, but it explains why an opened anhydrous liner in a humid room can change behaviour within a shift.

For the nonahydrate, ask for the bulk density and the mesh on the certificate rather than assuming they match the anhydrous range. Crystal habit and drying route differ between producers, and the number that matters is the one on the document for the lot you are buying. The bulk density entry explains how the figure is measured.

What changes in the finished product

The fill weight is the first consequence. At 16.2% magnesium, 100 mg of elemental magnesium needs about 617 mg of the anhydrous salt; at 11.9%, the same dose needs about 840 mg of the nonahydrate. On a fixed 500 mg capsule fill, the two grades deliver about 81 mg and about 60 mg of magnesium, so a 100 mg label claim that ran in one capsule on the anhydrous grade may need a larger capsule or a second one on the hydrate.

Capsule geometry compounds the arithmetic. A size 00 capsule at the dense end of the range holds roughly 600 mg of this powder, which is about 97 mg of magnesium from the anhydrous grade and about 71 mg from the nonahydrate at a similar density. Those are estimates, not fill-weight guarantees: the press trial and the certificate decide the final figure.

The label is the second consequence. In the European Union the ingredient list names the magnesium source as listed for food supplements, and the nutrition declaration reports magnesium in milligrams and as a percentage of the 375 mg reference intake. If the powder weight stays the same while the hydrate changes, the declared magnesium moves by roughly a third — a change that needs a new label, not a note in the batch file. The compliance page takes the labelling rules further.

Taste and dissolution favour the hydrate in some formats. Both grades dissolve, but the nonahydrate is the salt most often used in sticks and beverages, where it disperses readily; the citrate note is salty-sour and grows with dose, so the matrix has to carry it either way. In a capsule or a tablet the taste is irrelevant and the mass per dose is what matters.

How to write the specification

  • “Magnesium citrate, anhydrous, 14.5–16.4% Mg by complexometric EDTA titration.”
  • “Citrate identity by reaction and infrared spectrum, conforms to reference.”
  • “Loss on drying ≤2.0%; pH of 5% suspension 5.0–8.0.”
  • “≥95% through 40 mesh; bulk density 0.50–0.80 g/mL.”
  • “No added magnesium oxide, magnesium carbonate or citric acid.”

For the nonahydrate, replace the first line with the hydrate name and its own magnesium range, and replace the drying limit with the water figure the grade is sold against. A specification copied from the anhydrous line and applied to a hydrate will fail every lot, and the supplier will be right.

When not to switch

A hydrate switch is the wrong answer to a problem the grade did not cause. If a capsule is at its fill limit and the label has room to be recalculated, the anhydrous salt buys headroom — but the stability data, the label and the approved specification all belong to the old grade, so the move is a change control rather than a substitution.

If the nonahydrate flows well, dissolves in the intended matrix and the label has room for the extra mass, it is a legitimate choice and there is nothing to upgrade. The reverse is also true: paying for the concentrated grade is only worth something when the fill weight, the capsule count or the freight actually depend on it. The fill-weight page works the arithmetic through, and the COA page shows where the hydrate is declared on the certificate.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation