06 Identity & adulteration

How we prove a magnesium citrate lot is the nonahydrate

Technical document 06 · Reviewed 2026-11-20 · Magnesium Citrate Nonahydrate

On this page
  1. Four checks, one material
  2. The formula as a cross-check
  3. Diffraction and the crystal
  4. Routes and their fingerprints
  5. Writing the identity into the specification
  6. Five questions that build a file

A nonahydrate claim is supported by three agreeing results: citrate identity for the anion, an EDTA magnesium figure inside 11.0–12.5%, and a Karl Fischer water figure inside 24.0–28.0%. The water result is what separates this grade from the anhydrous salt; the magnesium result on its own cannot. The lot code should tie the certificate, the specification and the retain together.

In one line

For a hydrate, identity is a composition check: the citrate proves the anion, the magnesium proves the metal, and the water proves which hydrate was packed.

Four checks, one material

A certificate can carry the right name and still not prove the powder. The checks below ask separate questions, and each needs its own evidence.

Checks used to identify the nonahydrate
CheckWhat it answersMethodEvidence
PaperworkIs the hydrate named?Name, CAS, formulaA claim, not a measurement
AnionIs citrate present?Citrate reaction; infraredThe organic acid
MetalHow much magnesium?EDTA titrationThe quantity
WaterWhich hydrate?Karl FischerThe crystal water
PhaseIs it crystalline?XRD on requestThe solid form

The paperwork check is the label on the bottle; the other four are measurements. Anion plus metal plus water is the minimum set for a hydrate. Diffraction is the tie-breaker when the first three do not agree.

The formula as a cross-check

Three magnesium ions balance two citrate ions, so the anhydrous formula is Mg3(C6H5O7)2. Adding nine waters gives a molar mass near 613.2 g/mol, against about 451 g/mol for the dry salt. On the nonahydrate the theoretical split is roughly 11.9% magnesium, 61.7% citrate and 26.4% water, and those three figures account for the whole formula.

The number 8.41 (613.2 ÷ 72.9) turns a magnesium result into a nonahydrate equivalent. Read it as a mass-balance check, not a purity limit. A lot at 11.9% magnesium and 26.4% water matches the formula; a lot at the edge of both catalogue windows is still within the specification but is a different solid, and the pair belongs in the identity record. Citrate is qualitative in the catalogue, so a quantitative citrate result is an extra check.

A mismatch points to the next test. High magnesium with low water suggests a partly dehydrated or anhydrous fraction; low magnesium with high water suggests surface moisture or a diluent. Neither direction proves the cause, but both tell the laboratory what to run next. The hydrate entry explains the general arithmetic.

Diffraction and the crystal

X-ray diffraction sees crystalline phases. It can tell the nonahydrate from an anhydrous or partly dried phase, and it can detect crystalline magnesium oxide that the EDTA titration cannot distinguish. It does not measure purity or the counter-ion. Ask for the reference pattern and the detection limit before accepting a match.

Use diffraction when the water and magnesium results disagree, when a new source is being qualified, or when the label names the nonahydrate and the sheet is silent on phase. A report that says “XRD conforms” but attaches no pattern or reference has added little. Infrared is the bond-level partner: it shows citrate and water bands but not the lattice. The XRD note and the FTIR note describe both techniques.

Routes and their fingerprints

Substitution routes for a nonahydrate lot
RouteWhat shiftsWarning signTest
Anhydrous or partly dried citrateWater low, magnesium highThe pair falls outside the hydrate windowKarl Fischer, EDTA, XRD
Magnesium oxideMagnesium high, no citrateMetal passes without the anionCitrate reaction, XRD
Magnesium carbonateMagnesium high, carbonate presentAcid test gives carbon dioxideAcid test, XRD
Citric acidMagnesium low, citrate highAnion rises without the metalCitrate assay, pH
DiluentMagnesium lowMass balance leaves a gapEDTA, Karl Fischer, balance

The most common failure is documentary: an anhydrous lot supplied against a nonahydrate line. The water result exposes it. Appearance is the least useful check, because white to off-white covers both grades and many blends.

Writing the identity into the specification

  • “Magnesium citrate nonahydrate; CAS 153531-96-5; Mg3(C6H5O7)2·9H2O.”
  • “EDTA magnesium 11.0–12.5%, measured on the powder as received.”
  • “Karl Fischer water 24.0–28.0%.”
  • “Citrate identity by reaction and infrared, with the reference named.”
  • “XRD available on request; state the detection limit.”
  • “No added magnesium oxide, magnesium carbonate or citric acid.”
  • “Mesh, metals, micro and lot traceability as listed.”

The prohibitions carry as much weight as the numbers. A specification that sets a magnesium range but never excludes an added mineral has left the door open.

Five questions that build a file

  1. Which hydrate is on the certificate, and which CAS number?
  2. Was the magnesium measured as received, or after drying?
  3. What is the Karl Fischer water result for this lot?
  4. Which citrate method and reference were used?
  5. If water and magnesium disagree, will you supply an XRD pattern or a joint test on the retain?

Five clear answers are an identity file. A magnesium percentage alone is a number. The hub holds the catalogue line; the COA page shows where each result sits; the grade page compares the two solids; the EDTA note explains the titration; the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation