What the COA for magnesium citrate nonahydrate contains
A magnesium citrate nonahydrate certificate has to be read as a pair of numbers: the magnesium titration and the Karl Fischer water. The catalog puts magnesium at 11.0–12.5% and water at 24.0–28.0%, with citrate identity, contaminants, microbiology and an 80 mesh sieve line around them. The specification is the catalogue target; the lot certificate is the evidence for one pack.
On a nonahydrate certificate the magnesium assay and the Karl Fischer water are two halves of one composition check, and neither line identifies the hydrate on its own.
What the sheet has to show
Three facts decide whether the powder is the named grade: the magnesium figure, the water figure and the presence of citrate. Everything else on the sheet describes purity or handling. A certificate that gives a magnesium percentage but leaves water to a footnote has skipped the line that separates this hydrate from the anhydrous salt.
| Test | Procedure | Limit |
|---|---|---|
| Colour and form | Visual | White to off-white powder |
| Magnesium | EDTA titration | 11.0–12.5% |
| Water | Karl Fischer | 24.0–28.0% |
| Identity | Citrate reaction; magnesium titration | Matches reference |
| Metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Micro | Plate count; absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
| Mesh | Sieve | ≥95% through 80 mesh |
No pH or bulk density is fixed for this grade in the catalogue. If either matters to the matrix or the capsule line, put it in the purchase specification; it will not appear on a standard certificate unless it was asked for.
The magnesium is reported as received
An assay run on a dried sample answers a different question. Drying drives off the crystal water, the sample mass falls, and the magnesium percentage rises toward the anhydrous figure of about 16.2%. The result may be analytically correct and still be the wrong material for this specification. The certificate should say that the assay is on the powder as received, with the water result next to it.
The formula gives the anchor. Mg3(C6H5O7)2·9H2O has a molar mass near 613.2 g/mol; magnesium accounts for 72.9 g/mol (11.9%) and the nine waters for 162.1 g/mol (26.4%). The catalogue windows sit around those values rather than on them, so a commercial lot has room for purity and handling differences. Two lots at opposite corners of the two windows are not the same powder.
Karl Fischer is specific to water. Loss on drying sees whatever evaporates under the oven programme, and on a nonahydrate that is largely the water of crystallisation. A supplier who offers a loss-on-drying result of ≤2.0% against this grade has sent the anhydrous limit, not a better batch.
The gate and the measurement
A limit tells the reader what the lot had to meet; a result tells the reader what it measured. The certificate needs both, and the method has to sit in the same row. Repeating the specification range in the result column is not a batch result.
| Test | Limit | Result entry |
|---|---|---|
| Magnesium | 11.0–12.5% as received | Measured percentage; state the titration |
| Water | 24.0–28.0% | Measured percentage by Karl Fischer |
| Identity | Matches reference | Method, reference and comparison date |
| Metals | Each element | mg/kg for every element |
| Micro | Counts and absence | Count plus absence statement |
| Mesh | ≥95% through 80 mesh | Measured pass percentage |
For identity, “matches reference” is enough only when the method and the reference are named. For magnesium and water, the reader needs a figure. For metals, a single total hides which element drove it.
Why two lots differ
Water and magnesium are linked through the mass balance. A lot that retains more water shows a lower magnesium percentage; a lot that has lost water shows a higher one. That is why the two lines should be read together and why a drift in either is a reason to open the drying record. The crystal form is the other variable, and diffraction is the test that sees it.
Milling and sieving move the 80 mesh result without touching the chemistry, so a mesh change is a process event, not a purity event. Colour is a weak signal: a grey cast can come from metal contact, a hot dryer or a different magnesium source while the assay and water remain inside the limits. Bulk density is absent from the catalogue but decides capsule fill; request it when the fill weight is tight.
Finally, check the identifier. The lot code on the sheet, the pouch, the drum and the retain should be one code. A correct certificate for a different lot does not release the pack in front of you.
When an outside laboratory helps
Four situations justify the cost: an unknown supplier, a first entry into a regulated market, a label that claims the nonahydrate, or a disagreement over water or magnesium. The panel should close the gaps in the supplier's sheet rather than repeat it: EDTA magnesium, Karl Fischer water, citrate identity by reaction or infrared, ICP-MS metals and a micro count.
Add diffraction if the hydrate itself is disputed. It can tell a crystalline nonahydrate from an anhydrous or partly dried phase, and it can find crystalline magnesium oxide that a magnesium assay cannot distinguish. Request the reference pattern and the detection limit; without them “XRD conforms” is an opinion.
Send the retain, the supplier's certificate and your specification as one package. A referee needs the method and the limit as much as the sample, and a joint test on the retain is more useful than a second certificate from another drum.
A supplier comparison that works
Compare seven entries, not one: hydrate name and CAS; magnesium result and basis; Karl Fischer water and method; citrate identity method and reference; mesh and bulk density; contaminant and micro panel; pack size and lot code. A quote that omits the hydrate has not described a grade, and two sheets that agree on magnesium but differ on water describe different solids.
The catalogue line is on the nonahydrate hub. The grade page explains the hydrate trade-off, the identity page lists the tests that separate the two solids, the EDTA method note covers the magnesium assay, and the quality page shows how the release file is assembled.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation