01 COA & batch testing

What the COA for magnesium acetate actually contains

Technical document 01 · Reviewed 2026-11-20 · Magnesium Acetate

On this page
  1. The certificate as a single sheet
  2. What the assay is measured against
  3. Release limit, batch result and the word “conforms”
  4. What moves between batches
  5. When to send a lot to a second laboratory
  6. What to compare between suppliers

A magnesium acetate certificate reports appearance, identification of magnesium and acetate, the titration assay, elemental magnesium, water by Karl Fischer, the heavy-metal panel, microbiology and particle size. The two figures that decide how the rest is read are the assay basis and the water, because the catalog material is a hydrate with 25.0–30.0% water. The sheet is useful only when each line carries its method and its release limit.

In one line

The assay, the magnesium figure and the water are one statement: a 99.0–101.0% titration result means little until the certificate says whether it is on the dried basis and which water figure sits beside it.

The certificate as a single sheet

A release certificate is written against a specification, so each row has three parts: parameter, method and release limit. A result that stands alone cannot be repeated by a second laboratory, and a limit without a result is a promise rather than a measurement. The table below is the catalog specification for the tetrahydrate powder; the batch COA is the record for one lot.

Release lines · magnesium acetate tetrahydrate
ParameterMethodRelease limit
AppearanceVisualWhite to off-white powder
IdentificationMagnesium reaction and acetate reactionConforms to reference
Assay (dried basis)Complexometric magnesium titration with acetate titration99.0–101.0%
Magnesium (Mg)Complexometric titration or ICP-OES11.0–12.5%
WaterKarl Fischer25.0–30.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

What the assay is measured against

The assay is reported on the dried basis. The laboratory measures the powder, determines the water separately, and expresses the salt as a percentage of the dry matter. With water at 27.0% and an assay of 99.5% dried, the powder as weighed is about 72.6% magnesium acetate. The elemental magnesium then follows at about 12.4%, because the anhydrous salt is 17.1% magnesium by mass. A 99.5% figure read as an as-is result would imply more salt than the powder can contain, so the basis is not a footnote; it is the meaning of the number.

The water line is measured by Karl Fischer, not by loss on drying alone, because a hydrate releases water differently from surface moisture. The catalog sets 25.0–30.0%. A result at the top of that band carries less salt per kilogram, and a result at the bottom carries more; the magnesium figure moves in the opposite direction. Read assay, water and magnesium as a set, not as three independent passes.

The identification line has two halves. The magnesium reaction shows the cation, and the acetate reaction shows the anion; neither alone proves the salt. The assay method should name both titrations, the complexometric magnesium step and the acetate step. If the certificate reports one assay figure with no method, ask which titration produced it and whether the acetate was measured or calculated.

Release limit, batch result and the word “conforms”

A release limit is the gate; a batch result is the measurement. The sheet needs both, in the same row as the method. “Passes specification” is a conclusion, and the reader should be able to reach it from the numbers on the page.

What the result column should contain
ParameterRelease limitResult column
Assay99.0–101.0% driedA measured percentage, with water beside it
Magnesium11.0–12.5%A measured percentage and the method
Water25.0–30.0%A measured percentage by Karl Fischer
Heavy metalsPer elementA figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot
Particle size≥95% through 80 meshThe measured percentage through the sieve

“Conforms” is acceptable for identity when the reference and the method are named. It is not acceptable for assay, water or magnesium, which are numbers inside ranges. A certificate that reports a single heavy-metal total has hidden the element that matters; the panel is read element by element.

What moves between batches

Water is the largest moving line. Drying time and the humidity at packing move it within the band, and an opened pouch moves it after release. The assay on the dried basis should stay close to 100%; the as-is mass of salt falls as water rises. A lot with a low magnesium figure and a high water figure is internally consistent, not necessarily out of specification.

The acetate-to-magnesium ratio is the second check. A genuine salt holds about two moles of acetate per mole of magnesium. A figure that drifts away from that ratio points to residual acetic acid, a different magnesium source or a blend. Particle size follows the 80 mesh sieve and the mill; colour follows the drying step and the source. A faint acetic odour is normal for the salt and is not a defect on its own.

When to send a lot to a second laboratory

Order an independent test for a new source, a first shipment into a regulated market, or a disputed lot. The useful panel is magnesium by ICP-OES, acetate by ion chromatography, water by Karl Fischer, the heavy-metal panel by ICP-MS, microbiology, and an XRD or FTIR scan for the solid form. Magnesium and acetate together prove the salt; the water closes the mass balance; the certificate’s titration alone does not.

Add a sulfate and chloride screen if another magnesium salt is suspected, and ask for the detection limit of each screen. “Not detected” without a limit says something about the method, not the sample. Keep the retained sample with the lot code and send the same sample to the referee.

What to compare between suppliers

Compare six lines: form and CAS number; assay and its basis; magnesium figure and method; water by Karl Fischer; acetate identity and ratio; contaminants, mesh and pack. Two certificates that agree on assay but differ on water are describing different powders.

The catalog line sits on the magnesium acetate product page. The tests that separate the salt from sulfate, chloride or citrate are on the identity page; the hydrate arithmetic is on the grades page; the titration is described in the complexometric method note; the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation