02 Grade comparison

Magnesium acetate tetrahydrate or anhydrous: choosing a grade

Technical document 02 · Reviewed 2026-11-20 · Magnesium Acetate

On this page
  1. The hydrate is part of the identity
  2. The grades side by side
  3. Solubility, flow and the dry room
  4. What the grade does to the fill weight
  5. How to write the specification
  6. When not to switch

Magnesium acetate is supplied as the tetrahydrate powder specified here and as the anhydrous salt. The tetrahydrate carries 25.0–30.0% water and 11.0–12.5% magnesium; the anhydrous form carries about 17.1% magnesium and no water of crystallisation. The choice changes the mass per dose, the way the powder behaves on the filling line and the specification the lot is released against. Granulated and milled versions are process variants of one of those two forms, not a third chemistry.

In one line

The grade is a water decision first: the tetrahydrate carries 25.0–30.0% water and 11.0–12.5% magnesium, while the anhydrous salt carries about 17.1% magnesium and a much stronger pull on moisture.

The hydrate is part of the identity

The catalog form is the tetrahydrate, CAS 16674-78-5, formula C₄H₆MgO₄·4H₂O. The anhydrous salt is the same magnesium acetate without the water of crystallisation, CAS 142-72-3. The two are not interchangeable by weight: a kilogram of the tetrahydrate contains about 110–125 g of magnesium, while a kilogram of the anhydrous salt contains about 171 g. A formula written for one and weighed with the other misses the label claim by a wide margin.

Water of crystallisation is part of the lattice, not surface moisture that a dryer can remove at will. The 25.0–30.0% band is the release window for the catalog grade; the lot’s own water figure is what sets its magnesium content. The hydrate name alone does not fix the mass, which is why the certificate and the specification both carry the water line.

The grades side by side

Magnesium acetate grades · what changes between them
GradeWaterMagnesiumFitsWatch
Tetrahydrate powder, 80 mesh25.0–30.0% (Karl Fischer)11.0–12.5%Capsules, tablets, powder blendsHygroscopic; water sets the mass
Anhydrous powderNone in the lattice; picks up moistureAbout 17.1%Dry blends, non-aqueous systemsDeliquescent; needs a tight pack
Granulated tetrahydrateAs the base gradeAs the base gradeTablets, sachetsGranulation aids must be declared
Milled tetrahydrate, finer meshAs the base gradeAs the base gradeCapsules, suspensionsDust, flow, blend segregation

The last two rows are process variants, not different chemistry. Milling and granulation change the particle size, the flow and the dust; they do not change the magnesium figure, and they should not be used to explain one. If a supplier offers a “granular grade” with a different assay, ask which base salt it was made from.

Solubility, flow and the dry room

The tetrahydrate is freely soluble in water and gives a solution that is neutral to slightly acidic. It is also deliquescent: left in a humid room, it draws water, cakes and can turn from a free-flowing powder into a sticky mass. The 80 mesh line (≥95% through 80 mesh) describes the standard powder. A granulated form flows differently and is chosen for a tablet or a sachet line, not for a higher assay.

The anhydrous salt dissolves readily as well, but it has a stronger driving force to pick up water because it can move toward a hydrate. In a dry blend this is a handling problem; in a tablet it can show up as sticking or as a slow drift in weight. The catalog does not set a bulk density for magnesium acetate; if the fill weight depends on it, ask for the figure on the lot rather than assuming a range.

pH is a supporting check, not a grade marker. The solution is neutral to slightly acidic at the concentrations used in a drink mix; a low pH with a normal assay can point to residual acetic acid, and a high pH to a different magnesium source. Measure the solution as it will be used, not only the powder.

What the grade does to the fill weight

The fill weight follows the magnesium figure. To deliver 100 mg of elemental magnesium, the tetrahydrate at 11.0–12.5% needs about 800–909 mg of powder; the anhydrous salt at 17.1% needs about 585 mg. In a 500 mg capsule, the tetrahydrate delivers about 55–62.5 mg of magnesium, while the anhydrous salt delivers about 85 mg. Those are arithmetic estimates; the capsule trial and the lot certificate decide the final fill.

The hydrate also changes the powder mass at a fixed magnesium dose, and with it the amount of acetate carried per milligram of magnesium. A stick pack built on the tetrahydrate carries more powder than one built on the anhydrous salt. That is a formulation decision, not a purity difference. The acetate versus citrate comparison takes the taste and label questions further.

On the label, the ingredient is “magnesium acetate”; the hydrate state belongs in the specification and on the certificate. A switch from tetrahydrate to anhydrous is a change of mass per dose even when the label name stays the same, so it needs a new fill weight, a new nutrition calculation and a stability check.

How to write the specification

  • “Magnesium acetate tetrahydrate, CAS 16674-78-5, C₄H₆MgO₄·4H₂O.”
  • “Assay 99.0–101.0% on the dried basis by titration; magnesium 11.0–12.5%.”
  • “Water 25.0–30.0% by Karl Fischer.”
  • “Identification: magnesium and acetate reactions conform to reference.”
  • “≥95% through 80 mesh; heavy metals and microbiology as listed.”
  • “Hydrate state and water range confirmed before the order.”

For the anhydrous grade, replace the name, the CAS number, the magnesium range and the water line with the figures for that salt. A specification copied from the tetrahydrate and applied to the anhydrous lot will fail every time, and the supplier will be right.

When not to switch

Do not move to the anhydrous salt only to save mass. If the formula is aqueous or the label claim is fixed, the tetrahydrate is the simpler choice; if the blend must stay dry, the anhydrous form may be worth the handling work, but it needs its own stability data and pack. A switch in either direction is a change control, not a substitution at the balance.

Do not accept magnesium citrate as a substitute for magnesium acetate either. It is a different salt with a different taste, solubility and label name; the level-four page sets out the comparison. The product hub carries the catalog specification, the COA page shows where the water and magnesium are reported, the MOQ page covers the packs, the hydrate glossary entry defines the terms, and the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation