01 COA & batch testing

What the COA for dried ferrous sulfate actually contains

Technical document 01 · Reviewed 2026-11-20 · Ferrous Sulfate Dried

On this page
  1. What each certificate line has to carry
  2. The iron basis, the hydrate and the water line
  3. Release limit versus batch result
  4. What shifts from lot to lot
  5. When an outside laboratory is worth it
  6. Six lines to compare across suppliers

A dried ferrous sulfate certificate carries appearance, iron and sulfate identity, iron by titration at 30.0–33.0%, loss on drying at ≤1.0%, the heavy-metal panel, microbiology and particle size. Iron is the assay for this article: there is no separate “ferrous sulfate 99%” line, and a percentage written as the salt is not the same as the percentage of the element. The limits below belong to the catalog specification; a batch COA ties them to one pouch or drum.

In one line

Iron is the assay: 30.0–33.0% Fe by titration, with the loss on drying beside it and the hydrate named in the header.

What each certificate line has to carry

Read the header first. It should name the article, give the CAS number on the specification, and identify the lot and the pack. A certificate that says only “ferrous sulfate” leaves the hydrate open, and the hydrate separates this article from the heptahydrate.

Each row needs the parameter, the method and the release limit. “Conforms” is a real result for identity when the reference is named. Iron, loss on drying and particle size are numbers, each in a row with the method beside it.

Identity, iron, moisture and contaminants · dried ferrous sulfate
ParameterMethodRelease limit
AppearanceVisualGray-white to off-white powder
IdentificationIron and sulfate reactions; titration and gravimetric sulfate as the referenceConforms to reference
Iron (Fe)Complexometric or redox titration30.0–33.0%
Loss on dryingGravimetric, with temperature and time stated≤1.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

The iron basis, the hydrate and the water line

The iron result is reported on the material as received. That is the figure a fill weight uses: 31.0% Fe means 31.0 g of iron in 100 g of powder, so a 65 mg fill carries about 20 mg of iron. A result converted to a dried basis is a different number and must be labelled as such; at a loss on drying near 1.0% the arithmetic moves little, but the label still has to name the basis.

The loss-on-drying line is not automatically a total-water figure. The nominal monohydrate, FeSO4·H2O, carries about 10.6% bound water by formula, and that water is part of the crystal rather than a surface contaminant. The ≤1.0% limit and the 30.0–33.0% iron window are release tests on different fractions; the iron figure is the practical control on the hydrate. If a specification needs total water, ask for Karl Fischer and name the method on the certificate.

A “ferrous sulfate assay” should not appear without its calculation. At 31.0% Fe the powder is about 94.3% ferrous sulfate calculated as the monohydrate, yet it sits inside the 30.0–33.0% iron window. A salt percentage and an iron percentage answer different questions, and only one of them is on this specification.

Release limit versus batch result

The release limit is the boundary the lot had to meet; the batch result is the number the laboratory obtained. Keep them in separate columns and put the method beside each one. If the result column simply repeats the range, the reader has been given the gate again rather than the measurement.

Limit and result in separate columns · dried ferrous sulfate
ParameterRelease limitResult column
Iron30.0–33.0%A measured percentage, with the method and the as-is basis
Loss on drying≤1.0%A measured percentage, with the test conditions
Heavy metalsPer elementA measured mg/kg figure for each element
MicrobiologyCounts and absenceA count plus an absence statement for the lot
Particle size≥95% through 80 meshThe measured percentage through the sieve

“Pb <3 mg/kg” is a statement about the method's limit; 0.4 mg/kg is a measurement. A single summed figure for heavy metals does not show which element is present. The ferric check is often missing as well: the total-iron titration does not separate Fe2+ from Fe3+. Ask for ferrous iron by redox titration beside a total-iron result, and read the gap as the ferric fraction.

What shifts from lot to lot

Iron and loss on drying move first. The 30.0–33.0% window is wide because the dried article is a mixture of hydrates rather than a single stoichiometric compound; a lot at 30.5% and a lot at 32.8% can both be correct. A batch at the top of the iron window and the top of the loss-on-drying window is an edge combination, and the two lines should be read together.

Colour moves from gray-white towards yellow-brown as ferrous iron oxidises to ferric. Colour is a weak quantitative signal but a useful trigger: ask for the ferric result and the batch record instead of rejecting on appearance alone. Particle size is a finishing specification, so a mill or sieve change can move the 80 mesh result without any change in the chemistry.

When an outside laboratory is worth it

Order an outside laboratory when the source is new, when a first shipment is entering a regulated market, when the hydrate is disputed, or when the label names the dried article. The useful panel is not a repeat of the certificate: ferrous iron by redox titration, total iron by ICP-OES, sulfate by gravimetric barium sulfate or ion chromatography, water by Karl Fischer, XRD for the hydrate, ICP-MS for the metal panel and a micro count.

Each screen should come with its detection limit; “not detected” without that limit says more about the method than about the powder. The laboratory should test the retained sample and put the lot code on the report. If a result is disputed, hand the referee the retained sample, the supplier's certificate and the specification, and ask for the tests that distinguish the hydrates, not another run of the same titration.

Six lines to compare across suppliers

Six lines make a useful comparison: article and CAS; iron result and basis; loss on drying; ferric figure; sulfate result; and traceability. If two quotes agree on iron but not on hydrate or basis, they are not quoting the same article.

Six certificate lines to compare across suppliers
LineWhat to askWhy it matters
Article and CASDried ferrous sulfate named, with the CAS number on the sheetThe hydrate controls the iron and water arithmetic
IronThe measured figure, its basis and the methodThe fill weight is calculated from this number
Loss on dryingThe measured percentage and the test conditionsLoss on drying is not automatically total water
Ferric ironThe gap between total and ferrous ironOxidation can pass the iron window
TraceabilityA lot code linking certificate, pack and retained sampleA correct certificate may describe another drum

The specification is on the dried ferrous sulfate product page. The tests that separate the hydrates are set out on the identity page; the heptahydrate is a separate article on the ferrous sulfate page; the titration method is described in the complexometric method note; the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation