06 Identity & adulteration

How we prove a lot is dried ferrous sulfate

Technical document 06 · Reviewed 2026-11-20 · Ferrous Sulfate Dried

On this page
  1. Four questions, four measurements
  2. The iron-to-sulfate ratio
  3. X-ray diffraction: the hydrate check
  4. What adulteration looks like
  5. Identity lines for the specification
  6. Five questions to put in writing

A dried ferrous sulfate lot is the named article when the iron titration, the sulfate check and the water figure agree with the specification, and the XRD pattern matches the hydrate reference. Iron alone cannot separate the dried article from the heptahydrate or from a dilution, because both are ferrous sulfate. The sulfate and water results are the second and third dimensions.

In one line

Three results have to line up: the iron titration, the sulfate figure and the water or XRD pattern, and each one rules out a different substitution.

Four questions, four measurements

Naming the article on the certificate is a start, not proof. Each layer below answers a different question and needs its own measurement; a supplier who stops at the first has sent paperwork rather than evidence.

Four layers of dried ferrous sulfate identity
LayerQuestionTestWhat it proves
DocumentIs the article named?Name, CAS number, formulaPaperwork only
IronIs the iron ferrous?Redox titration; total iron by complexometric titration or ICP-OESThe oxidation state and the iron content
SulfateIs the counter-ion sulfate?Gravimetric barium sulfate or ion chromatographyThe salt family, not the hydrate
HydrateWhich hydrate is it?Water by Karl Fischer plus the iron mass balance; XRD for the patternThe water of crystallisation

A mass-balance check sits across the four: iron plus sulfate plus water plus impurities should close to 100%. A result that leaves a large unexplained fraction points to a filler, a different salt or an analytical error.

The iron-to-sulfate ratio

Ferrous sulfate has one ferrous ion per sulfate ion. The molar ratio is 1:1, and the mass ratio is 55.85 ÷ 96.06 = 0.581. For a powder at 31.0% Fe, the sulfate content is about 53.3% and the water about 15.7%; at 33.0% Fe the sulfate is about 56.8% and the water about 10.2%. Those figures are the hydrate signature, and they move together.

A sulfate result that is high relative to iron suggests a sodium sulfate dilution; a sulfate result that is low suggests another iron salt or an iron oxide. Sodium by ICP-OES is the direct check for a sodium sulfate dilution. The same ratio separates ferrous sulfate from ferrous fumarate or ferrous gluconate, because those articles carry an organic counter-ion: sulfate is low or absent and carbon is present.

The water-to-iron ratio is the second ratio. The monohydrate has one water per ferrous sulfate; the heptahydrate has seven. A water figure that does not match either pattern, with a normal iron result, is a reason to ask for XRD rather than to accept the certificate.

X-ray diffraction: the hydrate check

X-ray diffraction answers the solid-state question: which crystalline hydrate is present, and does the pattern match a reference? The heptahydrate, the monohydrate and the anhydrous salt have different patterns, and a crystalline article can be distinguished from an amorphous dilution. The method does not measure purity or the counter-ion.

A “match” statement needs the reference pattern and the detection limit behind it. Sample preparation matters: grinding can change the pattern of a hydrate, and a damp sample can lose water in the beam. A sheet that says only “XRD conforms”, with neither pattern nor reference, gives the reader nothing to check.

XRD is most useful when the hydrate is in dispute, when a source is being qualified, or when a lot behaves differently in a solution or a blend. It is not a routine release test for every lot, and it does not replace the iron and sulfate results.

What adulteration looks like

Common dried ferrous sulfate substitutions and the signals
AdulterantWhat it doesSignalTest
Heptahydrate sold as driedRaises water, lowers iron per gramIron low; water high; wrong XRD patternIron, Karl Fischer, XRD
Ferric oxide or rustRaises total iron, lowers ferrous ironYellow-brown; ferrous/total gap; magnetic or insoluble residueRedox titration, XRD, solubility
Sodium sulfateDilutes iron and adds sulfate and sodiumSulfate high relative to iron; sodium presentSulfate, sodium by ICP-OES
Ferrous fumarate or gluconateAdds iron with an organic counter-ionSulfate low; carbon presentSulfate, FTIR or HPLC, carbon
WaterLowers iron as-is and raises loss on dryingIron at the low edge; moisture highLoss on drying, Karl Fischer

Appearance is the least specific evidence. Gray-white to off-white is a wide window, and a yellow-brown cast can be surface oxidation rather than a different article. The iron-to-sulfate ratio, the ferric fraction and the hydrate pattern carry more weight.

Identity lines for the specification

  • “Dried ferrous sulfate, CAS 7720-78-7, FeSO4·H2O nominal.”
  • “Iron 30.0–33.0% by complexometric or redox titration, reported as-is.”
  • “Loss on drying ≤1.0%, with the test conditions stated.”
  • “Identification of iron and sulfate; report the reference method.”
  • “Hydrate identity by Karl Fischer or XRD where the article is disputed.”
  • “Particle size ≥95% through 80 mesh; heavy metals and microbiology as listed.”
  • “No added sulfate, iron oxide or organic iron salt; ferric limit to be agreed.”
  • “Article name, CAS and hydrate on the COA and the label.”

Five questions to put in writing

  1. Which article is this lot: dried ferrous sulfate, the heptahydrate or the anhydrous salt, and which CAS number is on the certificate?
  2. What is the ferrous iron result by redox titration, and what is the total iron result by complexometric titration or ICP-OES?
  3. What is the sulfate result, and what is the iron-to-sulfate ratio?
  4. What is the water result by Karl Fischer, and does the XRD pattern match the declared hydrate?
  5. If the lot is disputed, will you re-test the retained sample jointly with us?

Those five answers, taken together, are the identity file; one iron figure is not. The product hub holds the catalog specification; the COA page tracks each figure back to the certificate; the grades page sets the dried article against the heptahydrate; the XRD method note explains the solid-state check; the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation