Dried ferrous sulfate grades: the dried article and the heptahydrate
Dried ferrous sulfate is the partially dehydrated article specified at 30.0–33.0% iron; the heptahydrate is the fully hydrated crystal at 19.5–20.5% iron and 45.0–48.0% water. The dried grade puts roughly half again as much iron into the same weight, so a dose needs a smaller fill and brings less water into the blend. Both are ferrous sulfate, and neither is a drop-in for the other.
Water, not purity, separates the two articles: the heptahydrate is about 20% iron and 45% water, the dried article is 30–33% iron with roughly 10–18% water, and that ratio sets the fill weight.
Why the dried grade exists
The two articles begin with the same ferrous sulfate. The heptahydrate is what crystallises out of water; the dried article is produced by removing part of that water, leaving a nominal monohydrate or a mixture of hydrates. The name describes a drying step, not a single chemical formula. That is why the specification has to carry an iron window and a loss-on-drying limit, not only the word.
Water is the reason the dried grade exists: in a dry dosage form it is weight the capsule does not need. Per kilogram, the heptahydrate delivers about 201 g of iron and the dried article about 310 g at 31%. At 25 kg the difference is about 2.7 kg of iron per drum, which shows up as inventory, freight and warehouse space as well as fill weight.
Purity is not what separates the two articles. Both can be high-purity and both can meet a heavy-metal panel. What changes is the mass of iron per gram of powder and the amount of water the formula has to carry.
The two articles side by side
| Property | Dried article | Heptahydrate |
|---|---|---|
| Formula | FeSO4·H2O, nominal | FeSO4·7H2O |
| CAS number | 7720-78-7 | 7782-63-0 |
| Iron content | 30.0–33.0% by specification | 19.5–20.5% by specification; 20.09% by formula |
| Water content | About 10.6% as the monohydrate; roughly 10–18% across the iron window | 45.36% by formula; catalog 45.0–48.0% |
| Iron per 100 mg | About 30–33 mg | About 20.1 mg |
| Mass for 20 mg iron | About 60.6–66.7 mg | About 99.6 mg |
| Appearance | Gray-white to off-white powder | Pale blue-green crystals or powder |
| Typical use | Capsules, tablets and dry blends | Solutions, syrups and crystal grades |
The masses above are calculated from the formulas; the batch certificate's iron result takes the place of the theoretical figure. Water is the other half of the comparison: the same 20 mg iron dose arrives with roughly 45 mg of water as the heptahydrate, against about 6–12 mg as the dried article.
Powder, crystals and handling
The catalog powder is specified at ≥95% through 80 mesh and is gray-white to off-white. It is free-flowing when dry, but it is hygroscopic: an open pouch picks up moisture, the powder cakes, and the surface can turn yellow-brown as ferrous iron oxidises. The heptahydrate is pale blue-green and crystalline, and it is efflorescent, so it can lose water in a dry store. Both need a sealed pack; the failure direction is different.
The mesh figure is set at the mill, not by the reaction: a new sieve can change it while the chemistry stays the same, and granulation is a separate article rather than a packing choice. A capsule line with a fixed volume needs the bulk density and the particle-size distribution, not just the mesh number.
Appearance is the least specific check. Gray-white to off-white covers a range, and a yellow-brown cast can be surface oxidation rather than a different article. Use the iron and ferric results before rejecting a lot on colour.
Fill weight and the iron declaration
Every calculation starts from the iron result, not from the salt weight. At 30.0–33.0% Fe, 20 mg of elemental iron is 60.6–66.7 mg of dried article; at 19.5–20.5% Fe, the same 20 mg is 97.6–102.6 mg of heptahydrate. At 40 mg the masses are 121.2–133.3 mg and 195.1–205.1 mg. These are examples, not a dose recommendation.
The formulator notices the water first. At 20 mg of iron, the heptahydrate contributes about 45 mg of water to the fill; the dried article contributes roughly 6–12 mg. A tablet can see the water move into the granulation, a capsule can see a softened shell or a moisture-sensitive partner, and a blend can see its water activity and caking behaviour shift.
In a 1 g stick pack, the dried article takes about 6.1–6.7% of the fill for 20 mg of iron; the heptahydrate takes about 9.8–10.3%. That changes the flow, the segregation risk and the amount of carrier the formulator needs. The label speaks in elemental iron, the order in salt weight, and the certificate's iron figure is the connection between them.
Lines for the purchase specification
- “Dried ferrous sulfate, CAS 7720-78-7, FeSO4·H2O nominal.”
- “Iron 30.0–33.0% by complexometric or redox titration, reported as-is.”
- “Loss on drying ≤1.0%, with the test conditions stated.”
- “Identification of iron and sulfate; report the reference method.”
- “Particle size ≥95% through 80 mesh; granulated on request.”
- “Heavy metals and microbiology as listed; ferric limit to be agreed.”
- “Hydrate, CAS and article name on the COA and the label.”
- “Destination market and intended dose confirmed before the order.”
A specification that names only “ferrous sulfate” describes a family, not a purchase: the family contains a 20% iron hydrate and a 30–33% iron dried article that behave differently on a fill weight.
When the heptahydrate is the better choice
A solution or a syrup is easier to build on the heptahydrate: it dissolves readily, and the water it brings is already part of the solvent. The dried article dissolves more slowly and offers no advantage in a liquid.
A label that names the heptahydrate rules out a silent switch: the declared ingredient and the weighed powder would differ. The dried ferrous sulfate product page carries the catalog specification; the level-four comparison takes the water and label questions further; the heptahydrate page covers the other article; the methods library describes the iron assay; the quality page covers release.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation