What the COA for calcium citrate actually contains
A calcium citrate certificate reports appearance, calcium by complexometric EDTA at 21.0–22.0%, assay on the dried basis at not less than 97.5%, citrate identity by reaction and infrared spectrum, loss on drying at not more than 13.0%, 80 mesh particle size, bulk density 0.60–0.95 g/mL, the heavy-metal panel and microbiology. Those are the catalog limits; the batch COA confirms the lot. The calcium figure is the one buyers read first, and by itself it does not prove the citrate.
A calcium figure near 21% fits the tetrahydrate, but only the citrate identity and the water figure show that the drum is calcium citrate.
The certificate as a test report
A calcium citrate certificate is read in three columns: the parameter, the method that produced the number, and the limit the lot was released against. Appearance and identity are pass or fail; calcium, assay, moisture and the physical results are numbers measured against windows.
| Test | Method | Acceptance range |
|---|---|---|
| Appearance | Visual | White, odourless, free-flowing powder |
| Calcium (Ca) | Complexometric EDTA titration | 21.0–22.0% |
| Assay (calcium citrate) | Calculated on the dried basis | ≥97.5% |
| Identification | Citrate reaction and infrared spectrum | Conforms to reference |
| Loss on drying | 150 °C for 4 hours | ≤13.0% |
| Test | Method | Acceptance range |
|---|---|---|
| Particle size | Sieve analysis | ≥95% through 80 mesh |
| Bulk density | Tapped cylinder | 0.60–0.95 g/mL |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
“Conforms” is right for the identification line, because the test is comparative. It is not right for calcium or assay, where a number and a basis belong on the page. A certificate that reports only “passes specification” gives a conclusion without the evidence.
EDTA, the dried basis and the water
Complexometric EDTA titration measures calcium, not citrate. The titrant binds the calcium ion at an alkaline pH, an indicator marks the endpoint, and the result is calculated as elemental calcium. The method is also blind to the anion: calcium carbonate at about 40% calcium and calcium oxide at about 71% would both titrate. The 21.0–22.0% window is the first identity clue, because calcium citrate tetrahydrate is 21.1% calcium by calculation, anhydrous citrate is 24.1%, and carbonate is 40.0%.
The assay is reported on the dried basis. The sample is dried and the result describes the salt without its water; the specification requires not less than 97.5% on that basis. Loss on drying is the other side of the same coin. The tetrahydrate carries four molecules of water, 12.6% of its mass, and the 13.0% limit covers that water plus a small amount of surface moisture. A result near 12% is a hydrate, not a wet lot; a result near 2% with calcium near 24% points to the anhydrous salt.
The two figures are not interchangeable. At 12.6% water, 21.1% calcium as sold becomes 24.1% on a dried basis, which is the anhydrous stoichiometric value. That is why the calcium window and the assay window can describe the same lot, one as sold and one after drying. The certificate should state the basis next to each figure. A result copied from one basis into the other is an arithmetic error, not a batch failure.
The windows are independent gates, and a lot must meet both. Pushing calcium to 22.0% and loss on drying to 13.0% at once leaves little room for the assay: the dried-basis calcium would sit above the anhydrous figure. Read the three lines together.
Release limit versus batch result
A release limit defines the gate; the batch result records what the laboratory found. Keep them in separate columns, with the method and the basis beside each. A result column that repeats the specification is not a result; a certificate that reports only a conclusion asks for trust without evidence.
Not every line needs a number. Identification is comparative, so “conforms” is correct; calcium, assay and loss on drying are numeric and need their own figures. Particle size should name the sieve, and bulk density the method, not only a single number.
The reader should be able to reach the release decision from the page: calcium inside 21.0–22.0%, assay at or above 97.5% on the dried basis, loss on drying at or below 13.0%, and the contaminant and micro results inside their limits. If any is missing, the certificate is incomplete rather than failed.
What moves between batches
Calcium and loss on drying move together, in opposite directions, with the hydration and drying route. A lot dried harder loses lattice water, calcium rises on the as-sold basis, and the assay on the dried basis may barely move. That is a hydrate change, not a potency change, and the certificate should be read with both figures in view.
Particle size and bulk density come from milling and sieving. The catalog window of 0.60–0.95 g/mL is wide enough that a dense lot and a light lot behave differently in a capsule or a tablet die. Colour and flow are less quantitative: a grey tint can follow the limestone source, and a change in flow often follows moisture. A trend across several lots says more than a single result near an edge.
When to order an outside test
An outside laboratory earns its place on a new source, a first entry into a regulated market, a contested result, or a citrate claim that the supplier's certificate does not carry. The useful panel is targeted: EDTA calcium on a stated basis, citrate identification by reaction and infrared spectrum, loss on drying, and ICP-MS for the heavy metals. An X-ray diffraction scan adds a check for crystalline calcium carbonate or oxide if the calcium figure is high or the citrate identity is weak.
Ask the laboratory to report its detection limit for any scan reported as not detected; a line without a limit describes the method, not the sample. The sample tested should be the retained sample, and the lot code should accompany it.
What to compare between suppliers
Compare six lines: the hydrate and formula; calcium with its method; assay with its basis; loss on drying; how citrate is identified; and the contaminant panel. If two quotations match on calcium and diverge on the other five, they describe different powders.
The second layer is traceability. The lot code on the certificate should match the drum and the retained sample, and the certificate should name the manufacturer and the plant. A correct certificate can still belong to a different drum, and a certificate without a lot code cannot be tied to the material on the dock.
The catalog figures are published on the calcium citrate product page. Salt choice is covered on the grade page; the tests that separate citrate from other calcium powders are on the identity page; release practice is described on the quality page. The titration itself is in the complexometric method note, and the water figure in the loss on drying entry.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation