What a calcium chloride dihydrate COA reports, line by line
The certificate for a calcium chloride dihydrate lot reports appearance, identification of calcium and chloride, assay by titration, elemental calcium, water by Karl Fischer, the heavy-metal panel, microbiology and particle size. Each line needs the method, the release limit and the measured result; the catalog range is a specification, and the batch COA confirms one pack. The form and the water figure belong on the same page as the assay: without them the percentage cannot be read.
The assay is only half the figure: a 99.0–101.0% titration belongs beside the 20.0–25.0% water result, because the dihydrate and the anhydrous salt are different products.
What the sheet has to show
A COA works as a set of claims that can be checked. For every parameter the reader wants the test, the acceptance boundary and the number obtained for the lot. When a line gives only a verdict, the evidence has disappeared; when it gives a number without a method, the number cannot be reproduced.
Here the identity evidence is split between two ions. Calcium is shown by the flame test and confirmed by the EDTA titration; chloride is shown by precipitation with silver nitrate. A certificate that reports calcium alone has not excluded carbonate, sulfate or a sodium chloride blend, which is why the chloride line belongs on the sheet.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | White to off-white powder |
| Identification | Calcium flame test and chloride precipitation | Calcium and chloride conform |
| Assay | Complexometric calcium and argentometric chloride titration | 99.0–101.0% |
| Calcium | Complexometric titration (EDTA) | 27.0–29.0% |
| Water | Karl Fischer | 20.0–25.0% |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
| Particle size | Sieve analysis | ≥95% through 80 mesh |
The hydrate basis, water and the calcium figure
Calcium chloride dihydrate is a defined compound, not a powder with a variable water load. Its formula gives 27.26% calcium, 48.23% chloride and 24.51% water, and the catalog ranges are drawn around those figures. A 100.0% result expressed as the dihydrate therefore contains about 75.5% calcium chloride; the other 24.5% is water of crystallisation, not filler.
Expressed as CaCl₂ instead, a 99.0–101.0% figure would point to a largely anhydrous powder, which is a different product. The certificate should state the basis in the assay row and print the Karl Fischer result alongside it. If a buyer needs the calcium chloride content, multiply the dihydrate assay by 0.755, or divide the calcium result by 36.11%.
Karl Fischer is the right water method for a hydrate. Heat-based loss on drying can drive off part of the water of crystallisation and leave a figure that is neither free moisture nor total water. The water result and the assay are a pair; reading one without the other is how a hydrate gets mistaken for an anhydrous salt.
The limit column and the result column
Two numbers sit behind every line: the limit the lot had to meet and the result the laboratory measured. They should never share a column. A result that repeats the range has not told the buyer what the lot contained, and a certificate that reports only “passes” has removed the data needed for a deviation or a trend.
| Parameter | Release limit | Result column |
|---|---|---|
| Assay | 99.0–101.0% | A measured figure, with the hydrate basis named |
| Calcium | 27.0–29.0% | A measured figure by the named titration |
| Water | 20.0–25.0% | A measured figure by Karl Fischer |
| Identification | Calcium and chloride conform | The two tests and what was observed |
| Heavy metals | Per element | One figure per element in mg/kg |
| Microbiology | Counts and absence | A count plus the absence statement |
| Particle size | ≥95% through 80 mesh | The measured percentage through the sieve |
A single total for heavy metals hides which element drove it; the file needs lead, arsenic, cadmium and mercury separately. Microbiology needs a count and an absence statement, because a count alone does not say whether Salmonella was tested. For identity, the test names are the evidence: “conforms” without the method is a conclusion, not a result.
What moves between batches
Water is the first variable. A sample left open in a humid room gains moisture within hours, and the water figure rises while the as-is assay falls. Powder taken from the top of a drum may not match the retained sample at the bottom. Crystallisation and drying move water and assay together; milling and sieving change the particle-size number without changing the chemistry.
The calcium and chloride results should move as a pair. A lot at the top of the calcium range and the bottom of the chloride range is not the dihydrate; it is a blend or another salt. Colour can drift from white to off-white with moisture and trace iron, a shift the catalog window allows, so appearance alone should not reject a lot.
Raw material source drives the trace metals. The limestone route and the brine route carry different impurity profiles, and lead is the usual watch item. A series of lots is more informative than a single certificate: water creeping upward, calcium drifting, or the calcium-to-chloride ratio shifting all point to a process change. The lot code on the paper should be the same one printed on the pouch and the drum.
When an outside laboratory earns its place
Outside testing is worth ordering at a new source, a first regulated shipment, a hydrate dispute or a result that does not reconcile with the batch record. The panel should be built for the question, not copied from the release sheet. For a hydrate dispute, calcium by EDTA, chloride by silver nitrate, water by Karl Fischer and XRD for the phase are the core; add ICP-MS and microbiology when the lot is new to the buyer.
Two details make the report usable. First, the detection limit: a statement that something was not found means little without the level at which the laboratory looked. Second, the sample identity: the report should name the lot, the pack and the retained sample so the result can be tied back to the material in the warehouse.
What to compare between suppliers
Compare the form before the assay: hydrate and CAS number, then assay with its basis, calcium and chloride, water, the metal and micro panels, particle size and pack. Two lots can match on assay and still differ on hydrate form, and the mass per dose then differs too.
Ask for the manufacturing source and the drying and milling route as well. Those records explain why two certificates with the same specification can behave differently in a capsule filler or a beverage line.
The catalog figures are on the calcium chloride product page; the grades page sets out the dihydrate and anhydrous forms; the identity page describes the tests that distinguish the salt from carbonate; the methods index covers the titration and water methods; the quality page explains how a lot is released.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation