06 Identity & adulteration

How to prove a lot is calcium chloride dihydrate

Technical document 06 · Reviewed 2026-11-20 · Calcium Chloride

On this page
  1. The four identity layers
  2. The calcium-to-chloride ratio and the water balance
  3. X-ray diffraction and the hydrate phase
  4. What substitution looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A calcium chloride dihydrate lot is proved when four measurements agree: the document names the dihydrate and CAS 10035-04-8, the calcium titration gives 27.0–29.0%, the chloride titration gives the proportion the formula predicts, and the Karl Fischer water sits near 24.5%. Calcium alone cannot separate the chloride from the carbonate, the sulfate or a sodium chloride blend. The ratio and the water are what close the case.

In one line

Calcium proves the element is present; the chloride figure, the water figure and the calcium-to-chloride ratio prove which salt it is.

The four identity layers

A certificate can name the right material and still fail to prove it. The four layers below are separate questions, and each one needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.

Four layers of calcium chloride dihydrate identity
LayerQuestionTestWhat it proves
DocumentIs the hydrate named?Name, CAS number, formulaPaperwork only
CalciumIs the element present?Flame test and EDTA titrationCalcium, not the salt
ChlorideIs the anion chloride?Silver nitrate titrationThe chloride anion
Water and balanceIs it the dihydrate?Karl Fischer water; calcium, chloride and water mass balanceThe hydrate form

The assay sits across the last three layers. A titration that reports 100% against the dihydrate formula is consistent with the calcium and water figures, but it can also be met by a blend that has been built to the same percentage. The ratio is the check that a single assay cannot provide.

The calcium-to-chloride ratio and the water balance

Pure calcium chloride dihydrate is 27.26% calcium, 48.23% chloride and 24.51% water by mass. That is a calcium-to-chloride mass ratio of 1:1.77 and a molar ratio of 1:2, with two water molecules for every calcium ion. The numbers are fixed by the formula, so a measured set that departs from them is describing a different material.

If calcium is high and chloride is low, the powder is likely a carbonate, an oxide or a sulfate. If chloride is high and calcium is low, sodium chloride is the likely blend. If both are near the formula but the water is low, the lot is partly anhydrous; if the water is high, it has picked up moisture or carries a diluent. The three figures should be read together, not one at a time.

The assay has its own basis trap. A 99.0–101.0% result expressed as the dihydrate is about 75% calcium chloride by mass; the same 99–101% read as CaCl₂ would describe a partly anhydrous powder, not this hydrate. A certificate that gives an assay without the form or the water has not said which number it reports, and two suppliers can quote the same percentage for different powders.

X-ray diffraction and the hydrate phase

X-ray diffraction answers the solid-state question: is the powder the dihydrate, the anhydrous salt, or a carbonate phase? The diffraction pattern of the dihydrate differs from the anhydrous salt and from calcite, so a pattern match can confirm the hydrate and expose a blend. XRD is not a purity assay and it does not measure the counter-ion; it is a phase check.

Sample preparation matters for a deliquescent salt. A sample left open can pick up water and change phase before the scan, so the powder should be loaded from a sealed container and scanned promptly. Ask for the reference pattern, the scan range and the detection limit before accepting a “match” statement. XRD is not a routine release test here; it is a qualification and dispute tool, and it is most useful when the question is the hydrate or a second crystalline phase.

What substitution looks like

Substitutions and the signals that expose them
SubstituteWhat it doesSignalTest
Calcium carbonateRaises calcium, adds no chloride; alkalineCalcium high, chloride low, acid effervescenceChloride titration, acid test, XRD
Sodium chlorideAdds chloride, dilutes calcium; saltyChloride high, calcium low, sodium detectedCalcium titration, sodium by ICP-OES
Calcium sulfateCalcium can sit near the right figure; no chlorideChloride low, sulfate detectedChloride titration, sulfate test, XRD
Anhydrous salt sold as dihydrateLowers water, raises calciumWater low, calcium high, assay above rangeKarl Fischer, calcium, XRD
Water or brine additionRaises water, lowers the assayWater high, calcium and chloride low togetherKarl Fischer, mass balance

Colour is the weakest signal: white to off-white covers the dihydrate, the anhydrous salt and a carbonate. The stronger signals are the chloride figure, the water figure and the ratio. A certificate that reports appearance and calcium but no chloride has left the most likely substitution untested.

The carbonate case is common enough to check first. The calcium carbonate page shows what the other salt's specification looks like; the acid test and the chloride titration separate the two quickly. The comparison page covers the solubility and pH consequences of that substitution.

How to write identity into the specification

  • “Calcium chloride dihydrate, CAS 10035-04-8, CaCl₂·2H₂O.”
  • “Assay 99.0–101.0% by titration, with the basis stated; calcium 27.0–29.0%; water 20.0–25.0% by Karl Fischer.”
  • “Chloride by silver nitrate titration, reported as a percentage where the form is in dispute.”
  • “Identification by calcium flame test, chloride precipitation and, where agreed, X-ray diffraction.”
  • “Particle size ≥95% through 80 mesh; heavy metals and microbiology as listed.”
  • “No carbonate, sulfate or sodium chloride added; hydrate form and water under change control.”

The negative clause gives the laboratory a line to test. A specification that does not exclude the carbonate and the sodium chloride leaves a blend inside the calcium window, and the chloride ratio is the only routine line that catches it.

Five questions for the supplier

  1. Which hydrate is this lot, and which CAS number is on the certificate?
  2. What are the calcium, chloride and water results, and how do they compare with the formula?
  3. Was the assay expressed as the dihydrate or as CaCl₂, and on which basis?
  4. Can you provide the XRD pattern and the reference, and was the sample protected from humidity?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file; a calcium percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grades page compares the hydrate forms; the methods index explains the titration and diffraction tests; the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation