06 Identity & adulteration

Proving a boron bisglycinate lot: name, spectrum, boron and glycine

Technical document 06 · Reviewed 2026-11-19 · Boron Bisglycinate

On this page
  1. The layers of the identity
  2. The glycine-to-boron ratio
  3. X-ray diffraction: what it can and cannot show
  4. What substitution looks like
  5. Writing the identity into the specification
  6. Five questions for the supplier

A lot is boron bisglycinate when four things agree: the document names the complex and the grade, the infrared spectrum matches the glycine–boron reference, the boron figure sits inside the declared window, and the glycine figure supports the ratio the specification states. Boron by ICP-OES on its own cannot separate the complex from boric acid, sodium borate or a glycine blend. With no CAS number to quote, those agreeing measurements are the identity.

In one line

With no CAS number to cite, identity rests on four agreeing measurements: the name, the infrared spectrum, the boron figure and the glycine figure.

The layers of the identity

Each layer answers a different question, and one result closes only one layer. A supplier who answers the first has described the paperwork; a supplier who answers all five has described the powder.

Identity layers for boron bisglycinate
LayerQuestionTestWhat it establishes
DocumentIs the complex and the grade named?Product name, boron figure, specification revisionWhat is being bought
InfraredIs glycine bound to boron?IR against a reference spectrumThe coordination, not the element
BoronHow much of the element is present?ICP-OESQuantity
GlycineIs the ligand present in the declared proportion?HPLC plus the calculated ratioThe ligand, not the solid form
BalanceIs anything else in the drum?Moisture, ash where measured, impuritiesWhether the numbers add up

The infrared layer is the one buyers most often skip, because it is the hardest to read from a certificate that says only "conforms". A spectrum of glycine and a spectrum of boric acid are not the same as a spectrum of the complex, and a physical mixture shows the sum of its parts. Ask for the spectrum, not only the word.

The glycine-to-boron ratio

The ratio is arithmetic on two measured results: moles of glycine divided by moles of boron. Boron has an atomic mass of 10.81 and glycine a molar mass of 75.07, so 100 g of powder at 5.3% boron carries 0.49 mol of boron. If the same 100 g reports 88% glycine, that is 1.17 mol of ligand and a ratio near 2.4. Those figures are an illustration, not a specification: they show how the two results combine into a single number that a buyer can compare across lots.

That number is a fingerprint rather than a molecular constant. The commercial complex is not a single stoichiometric salt, and the material typically carries ligand in excess of what a simple adduct would need, which is why the specification states a ratio to be held rather than a formula to be calculated. The catalog sets boron and asks for glycine to be reported; the ratio is calculated from the lot results and agreed with the supplier.

The ratio is also the most sensitive test for a blend. Boric acid carries about 17.5% boron, so a small addition lifts the boron figure and drops the ratio sharply; free glycine lifts the ratio and pushes boron toward the bottom of the window. Either change can leave the boron percentage inside 5.0–6.0%, and only the pair reveals it.

X-ray diffraction: what it can and cannot show

X-ray diffraction is not the identity test for this material. The complex may be amorphous, partly crystalline or a mixture, and a diffraction pattern without a reference phase cannot say which. A certificate that reports "XRD conforms" without the pattern, the reference and the detection limit has added a word rather than evidence.

Where XRD earns its place is on the adulterant side. Boric acid and sodium borate are crystalline and give sharp, recognisable patterns, so a scan can confirm or exclude a crystalline borate phase in a powder that also contains the complex. That is a narrower question than identity, and it is a useful one when a boron figure has moved without an explanation.

Ask what the laboratory compared against, and at what limit. A phase present below the detection limit will not appear, and a report that omits the limit has told the reader nothing about how much could be there.

What substitution looks like

Signals of common substitutions in boron bisglycinate
SubstitutionWhy it is usedSignalTest
Boric acidLifts boron at low addition; acidicRatio falls; solution more acidic; IR mismatchIR, ratio, pH
Sodium borateLifts boron; solubleSodium appears where the complex has noneSodium by ICP-OES
Free glycineBulks the powder; improves flowRatio rises; boron near the low edgeRatio, IR
CarrierDilutes a strong lot or a premixBoron and glycine both fall; moisture or ash risesMass balance, IR
WaterNone; it is pickup, not additionBoron falls as-is; loss on drying risesLoss on drying

Colour is the weakest signal of the five. A white powder can be the complex, a boric acid blend or a diluted premix, and no photograph separates them. The sodium figure, the ratio and the infrared spectrum are what carry the identification, which is why a certificate that reports only boron has left the most likely substitution untested.

Writing the identity into the specification

  • "Boron bisglycinate, glycine complex, standardised at 5.0–6.0% elemental boron by ICP-OES; no single CAS applies."
  • "Identification by infrared spectrum against a glycine–boron reference."
  • "Glycine by HPLC, reported with the basis; the glycine-to-boron ratio calculated and reported."
  • "Loss on drying ≤5.0%; appearance white to off-white, free-flowing; ≥95% through 40 mesh."
  • "No added boric acid or borate; sodium reported where borate is suspected."
  • "Crystalline borate phase screened by XRD on request, with the detection limit stated."

The clause about added boric acid is the one to keep in every revision. If the powder is blended after the complex is made, the blender owns the blend and issues the certificate, and the complex maker's certificate no longer describes the drum.

Five questions for the supplier

  1. What boron and glycine results belong to this lot, on what basis, and what ratio do they calculate to?
  2. Can you send the infrared spectrum and the reference it was compared against?
  3. Is the lot a single complex or a blend? If it is a blend, what else is in it and in what proportion?
  4. What is the sodium result, and does any crystalline borate appear in an XRD scan?
  5. If the form is contested, will you re-test the retained sample jointly with us?

Those five answers, taken together, are an identity file; a boron percentage on its own is not. The product hub carries the catalog figures; the COA page shows how each result is reported; the grades page works through the boron figure; the complex-versus-citrate page covers the ligand choice. The ICP-OES note and the FTIR note describe the methods, and the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation