5% or 10% boron: choosing a boron bisglycinate grade
Boron bisglycinate is bought on its elemental boron content, and the two commercial standards are 5% and 10% boron. The higher figure is not a purer material: it is a different ratio of boron to ligand, so it halves the powder weight needed for a given boron dose. Grade, particle size and any carrier then decide the fill, the flow and the label.
The grade is a boron-per-gram decision: 10% boron halves the powder weight for the same dose and leaves less ligand in the capsule.
Why the same product is sold in grades
The glycine–boron complex has no single CAS number and no fixed molecular weight, so "boron bisglycinate" on a purchase order does not state how much boron the powder contains. Suppliers standardise the material at a boron figure and sell it against that figure. The 5% grade is the one the catalog specification describes; the 10% grade is the same chemistry pushed to a higher boron load.
The two grades exist because the dosage form pulls in opposite directions. A capsule has room for a few hundred milligrams and no more; a tablet needs flow and compressibility; a powder blend needs the ingredient to disperse evenly at a low inclusion. The boron figure decides how much powder a dose costs, and the ligand share decides how much of everything else the formula has to carry.
A third variable is physical, not chemical: milled powder, granulated powder and a diluted premix can all be 5% boron and still behave differently on a tableting press. The grade is therefore a specification, not a brand name, and it should be written into the order with the boron figure and the particle size.
The grades side by side
| Grade | Boron | Powder per 1 mg boron | Fits | Watch |
|---|---|---|---|---|
| 5% standard | 5.0–6.0% | 17–20 mg | Capsules, tablets, blends | The catalog grade; the reference specification |
| 10% high-load | Around 10%; the limit is agreed | 10 mg | Small capsules, high-dose formats | Separate specification; ligand share falls |
| Granulated 5% | 5.0–6.0% | 17–20 mg | High-speed tableting, dusty blends | Mesh and bulk density move; assay does not |
| Diluted premix | Below 5% | More than 20 mg | Very low-dose blends | Carrier, label and fill weight all change |
The last row is a different purchase, not a repack of the parent powder. A diluted grade carries a carrier that has to be declared, and the label claim is built on the boron figure of the premix, not on the figure of the parent powder.
What the powder is like to handle
The catalog material is a white to off-white, free-flowing powder, soluble in water with a slightly acidic solution, and ≥95% passes 40 mesh. Solubility is what makes the 5% grade easy to use in a drink mix; it is also why an opened pouch needs to be resealed, because the powder takes up moisture and the loss on drying moves toward its 5.0% limit.
Bulk density is not the same on every grade, and it should be measured on the lot rather than taken from a data sheet written for a different mill setting. Two powders with the same boron figure can fill a capsule at different weights, which is why the capsule fill trial uses the actual lot. Dust and static are practical issues at 40 mesh: a granulated grade flows better and generates less dust, while its dissolution in a stick pack is slower.
Colour is a weak specification line on a white powder, but it is not useless. A batch that is noticeably off-white against its predecessor can point to a different drying step; the boron figure may still be in range. Record the appearance and compare it, rather than rejecting on a photograph.
Dose arithmetic and the fill
At 5% boron, one milligram of boron sits in about 20 mg of powder. At 10%, it sits in about 10 mg. A formula that declares 3 mg of boron per capsule therefore needs about 60 mg of the 5% grade or about 30 mg of the 10% grade. Neither figure is advice on intake; both are the arithmetic that links the label claim to the weigh-up.
The arithmetic has a second consequence. A 500 mg capsule filled with 60 mg of the 5% grade leaves 440 mg for the carrier, the flow agent and any other ingredient, and the blend has to be uniform at a 12% inclusion. The 10% grade halves the powder weight but not the uniformity problem, and at very low inclusion a granulated or diluted premix can disperse better than a fine powder. The formulator chooses between a smaller capsule and a more even blend.
Tablets add compression to the list. A powder that passes 40 mesh may still need granulation to run on a high-speed press, and granulation changes the bulk density and the mesh while leaving the boron figure alone. The label, in turn, declares boron as the element and names the form in parentheses, so the grade does not change the claim but does change the number of milligrams of ingredient behind it.
What to write into the specification
- "Boron bisglycinate, glycine complex; grade standardised at 5.0–6.0% elemental boron by ICP-OES."
- "Glycine by HPLC reported with the basis; the glycine-to-boron ratio calculated and reported."
- "Identification by infrared spectrum against a reference; no added boric acid or borate."
- "Loss on drying ≤5.0%; appearance white to off-white, free-flowing."
- "Particle size ≥95% through 40 mesh; granulated on request with the mesh stated."
- "Heavy metals and microbiology as listed; pack, lot code and specification revision on the certificate."
We supply the 5% grade. The 10% grade and any diluted or granulated variant are separate specifications, and the boron figure has to be agreed in writing before the order, because it changes the fill weight that the label is built on.
When a different grade is the wrong choice
If the capsule is already full, a higher boron grade does not solve the problem on its own: the dose per capsule has to be legal and sensible, and the label has to state the boron figure that the fill actually delivers. If the blend is very low dose, a fine 5% powder can segregate in the hopper, and a granulated or diluted grade is the practical answer.
If the label names the glycinate complex, a diluted premix may still be the right ingredient as long as the carrier is declared and the specification says so. What is not acceptable is a switch of grade at the last minute, after the label and the capsule size have been fixed. The grade decision belongs with the formula, the fill trial and the label, in that order.
The product hub carries the catalog figures. The COA page shows how boron and glycine are reported; the complex-versus-citrate comparison takes the ligand question further; the identity page gives the tests behind the form; the ICP-OES note describes the boron method.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation