What a boron bisglycinate certificate actually reports
A boron bisglycinate certificate has two jobs: report the elemental boron, and show that the boron is held by glycine rather than sitting in boric acid or a borate. The figures in the tables below are the catalog limits for the 5% grade, not results. A batch COA carries results for one lot, and with no CAS number to fall back on, the ligand line matters as much as the boron line.
The boron figure sets the dose and the glycine figure sets the identity; a certificate that reports only the first has not shown that the lot is the complex.
The three blocks on the page
Read a certificate in three passes. Identity comes first: appearance plus an infrared spectrum that matches the glycine–boron reference. Composition comes next: boron by ICP-OES and glycine by HPLC. Release comes last: moisture, the metal panel, microbiology and mesh. A document that carries only the third block describes a white powder, and a white powder could be several things.
| Test | Limit | Method |
|---|---|---|
| Boron | 5.0–6.0% | ICP-OES after acid digestion |
| Glycine | Reported for the lot | HPLC, with the basis stated |
| Identity | Matches the reference | Infrared spectrum |
| Moisture | ≤5.0% | Gravimetric loss on drying |
| Metal panel | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg | ICP-MS |
| Microbiology | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent | Enumeration and absence tests |
| Mesh | ≥95% through 40 | Sieve |
The glycine line is what separates a complex from a blend. Boric acid carries about 17.5% boron, so a modest addition lifts the boron figure a long way, and a mixture of boric acid and free glycine can be built to sit inside a 5.0–6.0% window with no boron–glycine bond in it. The element alone cannot expose that, which is why the ligand result belongs on the same page. The limit reads "reported for the lot" because the complex is not one stoichiometric salt; the way the ligand figure is used is worked through on the identity page.
As-is, dried, and what the percentage describes
Boron results are usually reported on the powder as received, and the catalog limit is written the same way, so a lot at 5.2% is read straight against 5.0–6.0%. A supplier who reports on the dried basis will show a higher number for the same powder: 5.2% as-is with 4.0% moisture becomes 5.42% once the water is divided out. Nothing has changed except the arithmetic, and nothing on the page will say so unless the basis is printed beside the result.
The figure a formulator can use is grams of boron per gram of powder, because that is what becomes a capsule fill. No line on the certificate measures the percentage of "complex". At 5% boron the greater part of the powder is ligand and water, so the complex share is inferred from the boron and glycine results together. That is the reason the two lines are more useful read as a pair than read alone.
Grade is part of the basis as well. A 5% specification and a 10% specification are separate documents with separate windows, and a certificate for one says nothing about the other. At 10% boron the powder weight for a given dose roughly halves, and the ligand share falls in proportion.
Limit, result and the line between them
The limit is where the lot is allowed to sit; the result is where it did sit. Both belong on the page, in their own columns, with the method named.
| Item | Gate | Evidence the lot should show |
|---|---|---|
| Boron | 5.0–6.0% | The measured figure, with its basis |
| Glycine | Reported for the lot | The measured figure plus the ratio to boron |
| Moisture | ≤5.0% | The as-received percentage |
| Metal panel | Per element | One figure in mg/kg for each element |
| Mesh | ≥95% through 40 | The share that passed the sieve |
A pass statement is a summary, and the reader should be able to rebuild it from the numbers. A heavy-metal line that gives a total has folded four measurements into one and hidden the element that matters. A microbiology line that says "absent" without naming the organisms and the test has hidden the method.
What shifts from lot to lot
Boron moves with the reaction ratio and with any blending step. Moisture moves with the dryer. Mesh moves with the mill, and colour moves with the drying history. Read across lots as a pair: boron flat while glycine falls suggests a carrier has been added; both falling suggests dilution; boron up while glycine falls suggests a borate or boric acid has been introduced.
Because the complex is not a single crystalline salt, boron is a manufacturing target rather than a physical constant. A producer who keeps 5.0–6.0% across lots is holding the reaction and the blend; a producer whose boron drifts across the window is holding neither. The trend across several lots says more than one certificate at the edge of the range.
The lot code on the page should lead back to the pouch, the drum and the sample the producer keeps. Without it, the certificate cannot be tied to any particular pack.
When to pay for an outside laboratory
An outside test earns its place when the source is new, when the lot is the first into a regulated market, when the form is contested, or when the documents hint at a blend. The panel that answers the form question is not a repeat of the certificate: boron by ICP-OES, glycine by HPLC, an infrared spectrum, moisture, sodium by ICP-OES, and a crystalline-phase check where a borate is suspected.
Sodium is the cheap tell. A glycine complex carries none; sodium borate does, and it is a common way to lift a boron figure. A sodium result above the reporting limit, with boron comfortably inside the window, is a question for the supplier rather than a line to file.
Ask each laboratory for its detection limit beside each screen. "Not detected" with no limit attached describes the reach of the method rather than the absence of the substance, and two laboratories can use the same words for results two orders of magnitude apart.
Comparing two suppliers
Six lines make the comparison: name and grade; boron with its basis; glycine with the calculated ratio; moisture; the metal and microbiology results; and pack, lot code and specification revision. Two offers can agree on the boron percentage while describing different grades or different bases, and in that case they are not offering the same material.
The catalog figures sit on the product hub. The tests that separate the complex from a boric acid blend are on the identity page; the market questions are on the compliance page; the boron method is described in the ICP-OES note and the ligand method in the HPLC note. The quality page sets out how a lot is released.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation