02.1 Complex vs citrate

Boron bisglycinate vs boron citrate: the complex, the boron and the fill

Technical document 02.1 · Reviewed 2026-11-19 · Boron Bisglycinate

On this page
  1. Two complexes, two identities
  2. The boron figure is the common currency
  3. What each one takes in fill weight
  4. Solution behaviour and pH
  5. What the label and the file have to say
  6. When to choose which

Both materials deliver boron, but they are different complexes with different ligands. Boron citrate is traded under CAS 74231-02-0 with a published formula of C6H5BO7 and about 5.4% boron; boron bisglycinate is a glycine complex with no single CAS, standardised at 5.0–6.0% boron. Because the two are standardised at similar boron figures, the capsule fill for a given dose comes out close. The ligand decides the identity, the solution, the label name and the route, not the milligram weight.

In one line

The boron figure sets the fill and the ligand sets everything else: identity, solution, label name and the market route.

Two complexes, two identities

Boron is a metalloid, not a metal, so neither material is a chelate in the sense that a zinc or copper bisglycinate is; the word is trade usage for a boron–ligand complex. Boron citrate pairs boron with citric acid, boron bisglycinate pairs it with glycine, and neither is a simple salt with one cation and one anion. The ligand is part of the identity.

The paperwork differs accordingly. The citrate has a CAS number and a formula a specification can cite; the glycinate has neither, so its specification states the boron figure and the ligand identity and proves both. A certificate for one material does not describe the other, even when the boron percentages agree.

Boron bisglycinate and boron citrate compared
PropertyBoron bisglycinateBoron citrate
LigandGlycineCitric acid
CAS numberNone for the complex74231-02-0
Formula lineNot fixed; the boron figure carries the specificationC6H5BO7, about 199.9 g/mol
Boron content5.0–6.0%; a 10% grade is also sold5.0–6.0%
Water solutionSoluble; slightly acidicSoluble; pH set by the grade
Label nameBoron glycinate or boron bisglycinateBoron citrate
Identity evidenceInfrared spectrum plus glycine by HPLCInfrared spectrum plus citrate

The boron figure is the common currency

Five per cent is a trade convention, not a natural constant. The citrate formula works out at 5.4% boron, and the commercial grade is bracketed at 5.0–6.0% for hydration and excess ligand. The glycinate has no formula to calculate from, so its boron figure is set by the reaction ratio and the drying step, and the 10% grade is a deliberate move up that scale.

Because the element is the same, the arithmetic that matters is the same. One milligram of boron is one milligram of boron whichever ligand carries it, and an intake assessment expressed as boron applies to the element rather than to the complex. That is convenient for the formulator and easy to misread on a label: the milligram figure in the supplement facts panel is boron, while the ingredient weight on the batch record is ten to twenty times larger.

What each one takes in fill weight

At 5% boron a 3 mg dose needs about 60 mg of either complex; at 10% the same dose needs about 30 mg of the glycinate. Those are arithmetic illustrations, not recommendations: the grade, not the ligand name, sets the powder weight.

The fill weight then sets the dosage form. A 500 mg capsule carrying 60 mg of powder leaves room for carrier and flow agent, and the blend has to be even at a 12% inclusion. Halving the powder weight with a 10% grade frees space but does not fix segregation, and a granulated grade disperses better at very low inclusion. A tablet adds compression: either complex may need granulation if the press runs fast, which changes the mesh but not the boron figure.

Fill weight is also where a supplier switch shows up. Two lots that both pass 5.0–6.0% boron can differ by a fifth in the powder needed for the same claim, one sitting at the bottom of the window and the other at the top. The weigh-up should use the lot result, not the midpoint of the specification.

Solution behaviour and pH

Both complexes are used in aqueous formats, and the solutions are not interchangeable. The glycinate solution is slightly acidic. The pH of a citrate solution is not fixed by the ligand name: commercial grades are specified from mildly acidic to near-neutral, because the complex is made from boric acid and citric acid and the ratio and the hydration vary. The pH of the grade in front of you belongs in the specification, not the reputation of the ligand.

The boron–ligand bond in water is an equilibrium, not a fixed structure. Dilution, pH and temperature all shift how much boron stays bound, which is why a concentrated stock and a finished drink are two different stability questions. A clear solution should be tested at the actual pH rather than assumed from the solubility figure.

For a capsule, solubility is a minor line: the powder is swallowed, not dissolved. For a stick pack or a drink it moves to the front of the specification, which makes it the cleanest basis for choosing a ligand.

What the label and the file have to say

A US supplement facts panel states boron in milligrams and puts the form in parentheses after the word boron, so "boron (as boron glycinate)" and "boron (as boron citrate)" are different declarations of the same element. The ingredient name on the panel has to match the material in the batch record, and a switch of ligand is a label change, not a purchasing detail.

In the European Union, boron appears in Annex I of Directive 2002/46/EC and the permitted forms are listed in Annex II, so the buyer's team checks whether the exact complex is one of the named forms. That is separate from the novel-food question: a 2025 consultation concluded that boron glycinate and boron bisglycinate are novel foods under Regulation (EU) 2015/2283, and the current record and texts should be checked as of the shipping date.

The citrate side follows the pattern of any other citrate mineral: the salt name, the hydrate and the elemental figure each carry part of the label, as the calcium citrate and magnesium citrate specifications show.

When to choose which

Choose the glycinate when the label names it, the file covers it, and the formula is built around an amino acid ligand. Choose the citrate when the label and the market file already name it, or when a citrate carrier suits the blend.

Neither is a drop-in for the other. A switch changes the ingredient name, the identity tests, the solution pH, the regulatory reference and, if the grade changes with it, the fill weight. It needs a change-control record, a fresh specification and a label review before the first batch, not a note on the purchase order.

The catalog specification is on the product hub; the grade arithmetic is on the grades page; the certificate lines are on the COA page; the tests behind the form are on the identity page; the route questions are on the compliance page. The methods library covers the ICP-OES and HPLC methods, and the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation