06 Identity & adulteration

How to prove a squalene lot is squalene

Technical document 06 · Reviewed 2026-11-19 · Squalene

On this page
  1. The identity layers
  2. The unsaturation ratio
  3. X-ray diffraction and the limits of the method
  4. What adulteration looks like
  5. How to write the identity into the specification
  6. Five questions for the supplier

A squalene lot is squalene when the GC assay, the refractive index and the iodine value agree, and the source record matches the certificate. Appearance cannot do the job: squalane is also a colourless oil, and a vegetable-oil dilution can look the same. The three figures answer three different questions — how much, which hydrocarbon, and how many double bonds.

In one line

Squalene identity is an agreement between three measurements: the GC assay, the refractive index and the iodine value, with the source record behind them.

The identity layers

A certificate can name the right material and still fail to prove it. The layers below are separate questions, and each one needs its own evidence. A supplier who answers only the first has described the paperwork, not the oil.

Layers of squalene identity
LayerQuestionTestWhat it proves
DocumentIs the material named?Name, CAS number, sourcePaperwork only
ChromatographyIs the main peak squalene?GC with a squalene standardThe hydrocarbon
RefractionDoes the optical property fit?Refractometry at 20 °CConsistency, not specificity
UnsaturationIs the oil unsaturated?Iodine value by WijsThe double-bond content
Mass balanceIs it diluted?Assay, moisture and iodine value togetherConsistency of the numbers

The unsaturation ratio

Squalene has six double bonds and a theoretical iodine value of about 370.7 g I₂/100 g. The catalog window is 350–380, which is roughly 94–102% of that figure. A saturated hydrocarbon such as squalane contributes almost nothing to the iodine value, so the figure is a direct measure of how much of the oil is unsaturated.

The ratio between the assay and the iodine value is the useful check. If a lot is 90% squalene and the remaining 10% were squalane, the expected iodine value would be about 0.9 × 370.7 = 334, below the 350 floor. A lot that reports 90% assay and an iodine value of 355 is therefore not a simple 10% squalane cut; the balance must contain other unsaturated hydrocarbons, or one of the two results is biased. The two lines together are stronger than either one alone.

The refractive index adds a third coordinate. Squalene sits at 1.494–1.499 and squalane at about 1.450–1.452, so a result near the lower end points to a saturated or diluted oil even when the assay looks acceptable. Temperature matters: report the refractive index at 20 °C, or correct it, because the value drifts with the cell temperature.

X-ray diffraction and the limits of the method

Squalene is a liquid at room temperature, so it has no crystal lattice and no useful X-ray diffraction pattern. XRD is not a release test for the oil, and a certificate that reports “XRD conforms” for a liquid should be read with care. Asking for a diffraction pattern as proof of squalene is asking the wrong test.

The technique earns its place in the powder-on-carrier format. There, XRD can show whether the carrier is crystalline or amorphous and can detect a crystalline diluent that the oil load figure does not explain. It describes the solid state of the carrier; it does not measure the squalene. Use GC, refractive index and iodine value for the oil, and keep XRD for the solid matrix.

What adulteration looks like

Squalene substitutions and the signals
AdulterantWhat it doesSignalTest
SqualaneSame skeleton, no double bondsIodine value near zero; refractive index near 1.451Iodine value, refractive index, GC
Vegetable oilAdds triglycerides and fatty acidsFatty acid methyl esters; saponification value risesGC after transesterification, saponification value
Mineral oilAdds saturated hydrocarbonsUnresolved GC hump; lower iodine value and refractive indexGC-MS, iodine value, refractive index
Partly hydrogenated squaleneReduces unsaturation without going to zeroIodine value between squalene and squalaneIodine value, GC profile
WaterRaises moisture; hazes the oilMoisture above 0.1%Karl Fischer

The most likely substitution is the one that looks identical: squalane. It is colourless, odourless and miscible with squalene, and the unsaturation figures expose it at once. A vegetable-oil dilution is easier to see on a GC run once the oil is transesterified, and the saponification value rises sharply because a triglyceride is an ester and squalene is not. Colour is the weakest signal of all.

Source claims are a separate question. The certificate can prove the hydrocarbon, but it does not prove that the oil came from olives. That is a traceability question: ask for the source declaration, the supplier's batch records and, where the claim is contested, a provenance investigation agreed with the laboratory.

How to write the identity into the specification

  • “Squalene, olive-derived, CAS 111-02-4, C₃₀H₅₀.”
  • “Assay ≥90.0% by GC; report the standard and the integration basis.”
  • “Refractive index 1.494–1.499 at 20 °C; report the temperature.”
  • “Iodine value 350–380 g I₂/100 g by Wijs.”
  • “Moisture ≤0.1% by Karl Fischer; heavy metals and microbiology as listed.”
  • “No squalane substitution; report any squalane peak above the agreed limit.”
  • “Source and distillation step declared; lot code matched to the retained sample.”

Five questions for the supplier

  1. What is the GC assay, and which standard and integration basis were used?
  2. What are the refractive index and its measurement temperature?
  3. What is the iodine value, and which method produced it?
  4. Can you provide the chromatogram and the source declaration, not only the certificate summary?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file. A single assay percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grades page compares the source and format options; the methods section explains the analytical approach; the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation