Phytosterols vs sterol esters: mass, solubility and the label
The free sterol is the crystalline sterol alcohol; the sterol ester is the same sterol with a fatty acid attached. The ester is oil-soluble, carries about 60% free sterol by mass, and appears on the label as a different ingredient, so the two are not interchangeable gram for gram.
Esterification adds a fatty acid, so a gram of sterol ester carries roughly 0.6 g of free sterol and behaves like an oil, not like the crystalline powder.
The bond that changes the ingredient
Both materials share the same sterol nucleus. The difference is the hydroxyl group at position 3: in the free sterol it is open, and in the ester it is joined to a fatty acid through an ester bond. The sterol moiety is unchanged; the molecule around it is not.
The mass difference is concrete. Beta-sitosterol has a molecular weight of about 414.7. A beta-sitosteryl oleate, with one oleic acid attached, is about 679.2. The fatty acid can be any food-grade acid, so the ester molecular weight and the sterol fraction move with the fatty acid profile of the batch.
That is why an ester specification cannot be written by copying the free sterol specification. The free sterol is sold on total sterol content, typically ≥95% by GC. The ester is sold on free sterol equivalent, usually 55–65%, together with acid value and peroxide value. A ≥95% total sterol limit applied to an ester would fail a good lot, because the fatty acid is part of the molecule.
The conversion and the label arithmetic
The conversion is a mass fraction, not a single molecular-weight ratio, because a commercial ester is a mixture of sterols and fatty acids. The usable figure is the free sterol equivalent on the certificate, commonly around 60%. One gram of ester at 60% delivers about 0.6 g of free sterol; one gram of the 95% powder delivers about 0.95 g of total sterols.
The arithmetic runs in both directions. A label that declares 500 mg of free sterols needs 500 ÷ 0.60 = 833 mg of ester at 60%. A label that declares 500 mg of ester delivers about 300 mg of free sterol equivalent. Neither figure is a dose recommendation; they are the calculations that keep the label, the fill weight and the certificate in agreement.
There is a second trap in the assay. The GC method used for total sterols saponifies the sample, so it hydrolyses the ester before measurement. The result is the sterol cargo, not the ester content. A certificate that reports only “total sterols ≥95%” on an ester has not shown the form; ask for the free sterol equivalent, the ester value or a free-sterol test beside it.
Solubility is the practical difference
The free sterol is a crystalline powder. It is insoluble in water, dissolves in hot oil only with heat and shear, and recrystallises as the oil cools. That makes it the natural choice for a capsule or tablet, and a difficult choice for a clear fat-based food unless the process is built around the crystallisation.
The ester is an oil or a waxy solid. It is miscible with edible fats, which is why it fits spreads, dressings, dairy analogues and oil-filled capsules. It is still not water-soluble: an ester in a beverage is an emulsion, not a solution. The formulator needs an emulsifier, a homogenisation step and a stability study in the matrix, not a stirring instruction.
For a dry blend, the free sterol powder can be carried on MCT powder or another carrier to improve flow and dispersion. A liquid ester does not become a powder by simple blending; it needs a carrier with enough absorption capacity, and the resulting powder is a different specification.
What the label and the entry have to say
The label names the ingredient, not the family. “Phytosterols” or “plant sterols” describes the free sterol; “plant sterol esters” describes the ester. The quantity needs a basis: milligrams of ester, milligrams of free sterol equivalent, or milligrams of total sterols. A label that gives a number without the basis invites a comparison that the product cannot support.
The source belongs on the label too, because the source sets the allergen and GMO statements. A soy-derived sterol and a sunflower-derived one are not the same declaration, even when both meet the same total sterol limit.
In the EU, the novel-food entry for phytosterols and phytostanols covers material presented as free sterols or esterified with food-grade fatty acids, with conditions on use and labelling. The entry that applies, and the current wording, are confirmed by the buyer's regulatory team for the destination; the entry is not a label approval. US labelling relies on the Supplement Facts panel, which has to name the form and the source in the way the finished product's route requires. The compliance page sets out the documents.
Stability follows the matrix
The free sterol is a crystalline solid with a melting range around 130–140 °C. Its main storage risks are oxidation at the particle surface, caking from moisture, and heat that softens or melts the powder. A sealed, dry, dark pack keeps it stable; an open pouch in a warm room does not.
The ester carries a fatty acid chain, which is an additional oxidation site. Peroxide value and acid value belong on its specification and in its stability protocol, and a hot hold with moisture can hydrolyse the ester. The ester is not automatically the less stable form; it fails in a different way, and the test panel has to match the failure mode. The stability page gives the protocol.
When to choose which
Choose the free sterol for capsules, tablets, dry blends and any label that declares phytosterols or plant sterols. It is the form with the ≥95% total sterol specification and the 80 mesh finish, and it is the form on the product hub.
Choose the ester when the matrix is a fat-based food or an oil capsule and the label can declare plant sterol esters. The ester is easier to disperse in fat and harder to declare as free sterol, so the label and the formulation should be decided together.
A switch in either direction is a reformulation: new fill weight, new label name, new specification and often new stability data. Put it through change control, and compare the certificate lines on the COA page before the first order.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation