02 Grade comparison

Free sterol powder or sterol ester: choosing a phytosterol grade

Technical document 02 · Reviewed 2026-11-19 · Phytosterols

On this page
  1. Why there is more than one phytosterol grade
  2. The grades side by side
  3. Powder, crystal and oil
  4. What the grade does to the dose
  5. What to write into the specification
  6. When another grade is the wrong choice

Phytosterols are supplied as a free sterol powder, as sterol esters and as diluted or granulated blends; the related stanols are a separate ingredient. The catalog grade here is the free sterol powder at ≥95% total sterols with a defined sitosterol, campesterol and stigmasterol profile; the ester is a different ingredient with a different sterol content per gram.

In one line

The grade is a dosage-form decision: the free sterol is a crystalline powder, the ester is an oil-soluble molecule, and the sterol mass per gram changes with the form.

Why there is more than one phytosterol grade

“Phytosterols” names a family of plant sterols, not one molecule. The family is extracted from vegetable oils or from tall oil, purified, and sold either as the free sterol or after reaction with a fatty acid to make a sterol ester. Stanols are the saturated relatives, and a diluted or granulated powder is the same sterol carried on a base or built into a coarser particle.

Each choice changes something the buyer can measure: the sterol content per gram, the solubility, the melting behaviour, the label name and, in some markets, the entry that covers the material. The source matters too, because a soy-derived mixture, a sunflower-derived one and a tall-oil one do not have the same sterol profile.

The grades side by side

Free phytosterol powder and phytosterol ester
PropertyFree sterol powderSterol ester
Total sterol content≥95.0% by GCRoughly 55–65% free sterol equivalent
Form at room temperatureWhite to off-white powderOil or waxy solid
Water solubilityInsolubleInsoluble
Fat solubilitySoluble in hot oil; recrystallises on coolingMiscible with fats and oils
Melting behaviourMelts around 130–140 °CNo sharp melting point as a mixture
Label namePhytosterols or plant sterolsPlant sterol esters
Typical dosage formCapsules, tablets, oil blendsSpreads, dressings, oil capsules
Sterol per gramAbout 0.95 gAbout 0.6 g

The last two rows are the ones that decide a project. A capsule formula is built on the powder; a fat-based food is usually built on the ester. A label that declares a sterol quantity has to state which basis it uses, because 1 g of ester is not 1 g of sterol.

Powder, crystal and oil

Free phytosterols are crystalline. The catalog powder is ≥95% through 80 mesh, white to off-white, and insoluble in water. In an oil it dissolves only with heat and shear, and it recrystallises on cooling; that behaviour is useful in some fat systems and a nuisance in others. The powder is not hygroscopic in the way a salt is, but it cakes if moisture is trapped in the pack, and the loss on drying limit of ≤2.0% is a release condition, not a storage cushion.

Sterol esters are oils or waxy solids at room temperature. They are miscible with edible fats, which is why they fit spreads, dressings and oil-filled capsules, and why they are not a drop-in for a powder capsule. A liquid or waxy ester has no 80 mesh finish; its physical specification is closer to an oil, with acid value and peroxide value beside the sterol content.

Stanols are the saturated analogues. They are a separate ingredient with a separate profile and label name, not a grade of phytosterol. A stanol product should be specified as a stanol, with its own sterol and stanol composition.

What the grade does to the dose

A 500 mg capsule filled with the 95% powder delivers about 475 mg of total sterols. The same label built on an ester at 60% free sterol equivalent needs about 833 mg of ester to declare 500 mg of sterols. The arithmetic belongs in the specification review, because the fill weight, the capsule size and the label quantity all move with it.

For an oil-based blend, the free sterol can be dissolved in hot oil and held in suspension or solution; the ester is easier to incorporate because it is already fat-soluble. A dry blend with MCT powder or another carrier is a third route: the carrier changes the flow, the dose per gram and the label, and the carrier's own specification has to be checked.

A tablet needs flow and compressibility; an 80 mesh powder may need granulation. A capsule can take the powder directly. A stick pack or a beverage is an emulsion project, not a dissolution step, because the sterol is not water-soluble. The dosage form should be settled before the grade is ordered, not after the first stability batch.

What to write into the specification

  • “Phytosterols, free sterol powder, source declared; CAS 83-46-5 for the beta-sitosterol reference.”
  • “Total sterols ≥95.0% by GC; beta-sitosterol 40.0–60.0%, campesterol 20.0–30.0%, stigmasterol 15.0–25.0%.”
  • “Loss on drying ≤2.0%; appearance white to off-white; particle size ≥95% through 80 mesh.”
  • “Heavy metals and microbiology as listed; the certificate states the basis of the sterol result.”
  • “For an ester: free sterol equivalent, acid value and peroxide value, in addition to the sterol profile.”
  • “Label name, source statement and destination market confirmed before the order.”

The CAS number belongs to beta-sitosterol, the principal sterol, not to the mixture as a whole; the specification should say so rather than imply that one CAS number defines every sterol in the powder.

When another grade is the wrong choice

If the label declares free sterols, an ester is not a drop-in: the mass changes, the label name changes and the sterol figure needs a conversion. If the process needs a clear aqueous solution, neither the powder nor the ester provides one; that is an emulsion or dispersion project with its own data. If the formula needs a high sterol load per gram, a diluted grade moves the fill weight in the wrong direction.

The catalog specification is on the product hub. The free sterol against the ester is compared in more detail on the level-four page; the release tests are on the COA page; the storage behaviour is on the stability page; the sieve terms are defined in the particle size glossary.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation