06 Identity & adulteration

How we prove a phytosterol ester lot is the ester

Technical document 06 · Reviewed 2026-11-20 · Phytosterol Esters

On this page
  1. Five pieces of evidence
  2. The sterol-to-ester ratio and the fatty acid
  3. X-ray diffraction: what it can and cannot do
  4. What adulteration looks like
  5. Writing identity into the specification
  6. Five questions for the supplier

An ester lot is identified by five agreeing measurements: the document names the ester and its CAS number, the GC assay gives the ester content and the sterol profile, a free-sterol test shows how much sterol is not esterified, a fatty acid profile shows what the sterol is esterified with, and the mass balance closes the numbers. The sterol profile alone proves the sterol source, not the ester form.

In one line

The sterol profile says which sterols, the ester content and free sterol say whether they are esterified, and the fatty acid profile says what they are esterified with.

Five pieces of evidence

A convincing identity file is built from measurements that point the same way. The document, the GC ester and sterol result, the free-sterol result, the fatty acid profile and the mass balance each answer a separate question; XRD is a sixth check when the solid form matters.

Evidence for a phytosterol ester identity file
EvidenceQuestion it answersWhat it proves
DocumentIs the form, CAS number and source named?Paperwork only
GC ester and sterol assayHow much is esterified, and which sterols are present?Ester content and sterol profile
Free sterolHow much sterol is not esterified?The extent of esterification
Fatty acid profileWhich fatty acid is attached?The fatty acid source and the ester type
Mass balanceDo ester, sterol, free sterol and acid value agree?Consistency of the numbers
XRD, where neededIs the solid crystalline, and does the pattern match?Solid form, not the sterol ratio

A supplier who answers only the document question has described the paperwork. A supplier who gives a sterol profile and no ester content has shown the cargo, not the form. The file is complete when the answers point at the same material.

The sterol-to-ester ratio and the fatty acid

The catalog sets ester content at ≥90.0% and total sterols at ≥55.0%. At the floor, 55 ÷ 90 = 0.61, so the ester itself is about 61% sterol by mass and the rest is fatty acid. A lot with 92% ester content and 57% total sterols is coherent; a lot with 92% ester content and 50% total sterols needs an explanation, because the two lines no longer describe the same molecule.

Free sterol is the direct check on esterification. If free sterol rises, ester content falls while total sterols can stay close to the same value: the sterol is still in the sample, but it is no longer esterified. Acid value may rise if hydrolysis released fatty acids. The catalog does not set a separate free-sterol limit, so ask for the result when the form matters and agree a limit for the application.

The sterol profile is the source fingerprint. The catalog requires the profile to conform to the agreed reference rather than fixing three ranges, so the specification has to carry the reference. Sitosterol, campesterol, stigmasterol and the minor sterols keep their pattern through esterification; a source change moves that pattern even when the ester content and total sterols stay inside the catalog. A profile that fits the source but an ester content below the floor points to a blend or a partly esterified lot.

The fatty acid profile is the second fingerprint. A phytosterol ester is a mixture of steryl esters, and the fatty acid distribution differs between sunflower-type, rapeseed-type and other food-grade sources. The specification should name the source or the profile. The melting behaviour, the flow and the oxidation rate follow the fatty acid, so a source change is a specification change, not a purchasing detail.

Normalisation is the quiet trap. Ester content, total sterols and free sterol must be reported on the same basis, as-is or dried, and the certificate should give the moisture result needed to convert between them. The catalog has no loss on drying line, so the basis has to be stated explicitly.

X-ray diffraction: what it can and cannot do

XRD answers solid-state questions. The neat ester is a paste or a waxy solid at ambient temperature, so a sharp crystalline pattern is not the routine expectation, and the absence of crystallinity does not mean the ester is absent. The pattern is more useful for the powder on carrier: it can show whether the carrier is crystalline or amorphous, whether crystalline free sterol is present, and whether two powders differ in solid form.

XRD cannot quantify ester content, total sterols or the fatty acid profile. A “match” claim that omits the reference pattern and the detection limit proves very little. For a disputed lot, use XRD alongside the GC, the free-sterol result and the mass balance.

What adulteration looks like

Phytosterol ester substitutions and their analytical signals
AdulterantEffectSignalTest
Free sterol addedEster content falls; free sterol risesEster low; total sterols may holdGC ester and sterol; free sterol
Vegetable oil dilutionEster and sterol per gram fall; fatty acid profile shiftsLow ester and total sterols; profile mismatchGC; fatty acid profile; mass balance
Excess carrierEster and sterol per gram fall; powder mass risesLow assay; carrier markersCarrier statement; ash; mass balance
Different fatty acid sourceSterol profile fits; fatty acid profile differsMelting and flow change; profile mismatchFatty acid profile
WaterHydrolysis; acid value and free sterol riseAcid value high; free sterol highAcid value; free sterol; moisture

Appearance is the weakest signal. A white paste looks like a white paste, and a powder on carrier looks like a powder. The stronger signals are the ester content, the free-sterol result, the fatty acid profile and the mass balance.

Writing identity into the specification

  • “Phytosterol esters, CAS 68441-68-9; form: neat paste or powder on carrier; carrier named.”
  • “Ester content ≥90.0% by GC; total sterols ≥55.0%; state the basis for each.”
  • “Free sterol: report the result and agree a limit for the application.”
  • “Fatty acid source or profile; the ester is a mixture, not a single fatty acid.”
  • “Acid value ≤1.0 mg KOH/g; peroxide value ≤5.0 meq O₂/kg.”
  • “Sterol profile conforms to the agreed reference; report the peak table.”
  • “Heavy metals and microbiology as listed; pack and storage condition.”

Five questions for the supplier

  1. Is the lot the neat ester or a powder on carrier, and what is the carrier level?
  2. What is the ester content, and was it read from the intact ester or calculated from the sterol and fatty-acid results?
  3. What is the total sterol result and its basis, and what is the free-sterol result?
  4. Which fatty acid source and profile does the lot carry, and does it match the declaration?
  5. If a result is challenged, is a shared re-test of the retained pack acceptable?

Those five replies form the identity file; a lone ester figure does not. The catalog specification is on the phytosterol ester hub; the certificate lines are on the COA page; the free-sterol comparison is on the phytosterol hub; the methods index explains the analytics; the quality page sets out release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation