How we prove a lot is sunflower phosphatidylserine
A sunflower phosphatidylserine lot is the named material when the PS assay, the phospholipid profile, the fatty acid and sterol pattern, and the source record agree. The PS assay alone cannot distinguish sunflower from soy, because the headgroup is the same. The source is proved by the lecithin feedstock and its lipid fingerprint, not by the word on the certificate.
A PS assay cannot tell sunflower from soy; the fatty acid and sterol profile, the phospholipid balance and the source record are what separate them.
The four identity layers
A certificate can name the right material and still fail to prove it. The layers below are separate questions, and each needs its own evidence.
| Layer | Question | Test | What it proves |
|---|---|---|---|
| Document | Are the material and source named? | Name, CAS number, source statement | Paperwork only |
| Chromatography | Is the phospholipid PS? | HPLC with the phospholipid profile | The headgroup, not the feedstock |
| Lipid fingerprint | Is the feedstock sunflower? | Fatty acid profile by GC; sterol profile | The plant source, within the method's limits |
| Mass balance | Is it diluted or oxidised? | PS, total phospholipids, loss on drying, peroxide and acid values | Consistency of the numbers |
The CAS number 1446756-47-3 identifies the phosphatidylserine molecule; it does not name the plant. Source is a separate specification line and a separate piece of evidence.
The ratios that carry the evidence
The first ratio is PS to total phospholipids. At the catalog limits it is 50 ÷ 70 = 71%. A lot at 55% PS and 70% phospholipids is 79%; a lot at 50% PS and 90% phospholipids is 56%. The ratio moves with the conversion yield and the feedstock, and it catches a powder that meets the PS line by adding a phospholipid carrier or by blending a concentrate down.
The second ratio is the fatty acid pattern. Sunflower lecithin is rich in linoleic acid (C18:2) with palmitic and oleic acids, and it carries little or no linolenic acid (C18:3). Soy lecithin carries a measurable linolenic fraction and a different sterol ratio, plus isoflavones that are specific to soy. Report the profile as percentages with the method, not as a qualitative note.
The third is the nitrogen-to-phosphorus ratio. PS has one nitrogen in the serine headgroup and one phosphorus in the phosphate, so the molar N:P is about 1:1. A low N:P points to phosphatidic acid or PI; a high one points to an amine carrier or a nitrogen-containing diluent. It is a supporting check, not a source test. The mass balance then ties PS, phospholipids, moisture and the non-phospholipid fraction together.
X-ray diffraction: what it can and cannot show
Plant phosphatidylserine is an amorphous solid, so X-ray diffraction gives a broad halo rather than a sharp pattern. It is not a PS identity test and it does not measure the source. What it can do is show a crystalline component: a sharp pattern where the specification expects an amorphous powder points to a crystalline carrier or a mineral diluent.
Use XRD as a limit test for crystalline carriers, not as a release test for PS. If a lot is disputed, the stronger combination is HPLC with the phospholipid profile, the fatty acid and sterol pattern, the PS-to-phospholipid ratio and the mass balance. Ask for the reference pattern and the detection limit before accepting a conforms statement.
What adulteration looks like
| Adulterant | What it does | Signal | Test |
|---|---|---|---|
| Soy PS | Same PS headgroup; different feedstock | Linolenic fraction; sterol ratio; isoflavones | Fatty acid and sterol profile; soy-specific screen |
| Phospholipid carrier | Meets PS by weight but changes the profile | PS-to-phospholipid ratio shifts | Total phospholipids and profile |
| Crystalline diluent | Lowers PS per gram | Sharp XRD pattern; ash or mineral residue | XRD; ash; mass balance |
| Oxidised lipid | Assay may still pass | Peroxide and acid values rise; colour darkens | Peroxide value, acid value, appearance |
| Moisture | Lowers the as-is PS figure; cakes the powder | Loss on drying high | Loss on drying |
The hardest case is soy PS sold as sunflower PS, because the PS assay and the phospholipid figure can match. The fatty acid and sterol pattern is the practical discriminator, supported by a soy-specific screen with a stated detection limit. A soy-not-detected line without a limit is not evidence of absence.
How to write the identity into the specification
- “Phosphatidylserine (sunflower lecithin), CAS 1446756-47-3; PS ≥50.0% by HPLC.”
- “Total phospholipids ≥70.0%; report the phospholipid profile.”
- “Source: sunflower lecithin; fatty acid profile and sterol profile on file.”
- “Loss on drying ≤5.0%; peroxide value and acid value reported.”
- “Particle size ≥95% through 80 mesh; heavy metals and microbiology as listed.”
- “Soy statement: no soy ingredient; cross-contact controls as agreed.”
The source line is not decoration. Without it, the specification describes a phosphatidylserine powder that could come from either feedstock. With it, the certificate, the label and the market file can be checked against the same statement.
Five questions for the supplier
- Which lecithin feedstock is this lot, and where was it converted?
- Can you provide the HPLC chromatogram and the full phospholipid profile, not only the PS percentage?
- What are the fatty acid and sterol results, and do they match a sunflower reference?
- What are the peroxide value, acid value and loss on drying for this lot?
- If the source is disputed, will you accept a joint re-test on the retained sample?
Five direct answers amount to an identity file. A single PS percentage does not. The product page carries the catalog specification; the COA page shows where each figure sits; the grades page covers the grade ladder; the sunflower vs soy comparison covers the source decision; the soy page gives the other specification; the methods library describes the assays; the quality page covers release.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation