02 Grade comparison

Sunflower phosphatidylserine: what the grade and the particle form change

Technical document 02 · Reviewed 2026-11-20 · Phosphatidylserine Sunflower

On this page
  1. Why the grade is more than the PS percentage
  2. The grade ladder
  3. Powder, flow and the 80 mesh line
  4. Dose arithmetic and the label
  5. What to write into the specification

Sunflower phosphatidylserine is sold mainly as a ≥50.0% PS powder with ≥70.0% total phospholipids, so the grade question is what else is in the powder: the other phospholipids, the particle form and any dilution. The catalog grade here is the 50% powder at 80 mesh; a granulated form is a particle change, while a higher-PS concentrate or a lower-PS dilution is a different specification with its own certificate. The PS number alone does not tell you which one you have.

In one line

The grade is set by the PS content, the phospholipid figure and the particle form, not by the source name on the pack.

Why the grade is more than the PS percentage

Sunflower phosphatidylserine is made by converting sunflower lecithin phospholipids to PS, and the conversion does not reach 100%. The powder therefore contains PS, unreacted PC and PE, other phospholipids such as PI and PA, a little neutral oil and moisture. Two powders can both read 50% PS and differ in everything else.

The catalog grade is defined by three lines: PS ≥50.0% by HPLC, total phospholipids ≥70.0%, and ≥95% through 80 mesh. The phospholipid line limits how much of the powder can be non-phospholipid material. A 50% PS product with 55% total phospholipids would fail the catalog grade, whatever the label says.

Source is a separate axis. Sunflower and soy PS are compared on the sunflower vs soy page; this page is about the grade ladder within sunflower.

The grade ladder

Sunflower PS forms and what changes
FormPS / phospholipidsWhat it isMain consequence
Standard powder (catalog)≥50.0% / ≥70.0%80 mesh powder from sunflower lecithinThe reference grade for capsules, tablets and blends
GranulatedSame chemistryGranulated powder, on requestBetter flow, less dust; particle profile changes
Higher-PS concentrateAbove 50%, separate specificationFurther enrichment or a different conversionLess powder per serving; its own COA and method
Diluted gradeBelow 50%, separate specificationPS powder on a carrierMore powder per serving; carrier and label change

The first row is what this catalog supplies. The other rows are separate specifications that exist in the market: a 70% concentrate is not a stronger version of the same pack, and a 20% dilution is not a packing choice. Each has its own PS figure, phospholipid figure and certificate, and the label has to name what is actually in the powder. This catalog does not list them.

Do not accept a grade switch on the PS figure alone. A granulated form should hold the same PS and phospholipid results; a concentrate or dilution should not. If the PS figure stays at 50% but the phospholipid figure moves from 70% to 90%, the powder has changed even though the headline number has not.

Powder, flow and the 80 mesh line

The standard powder is specified at ≥95% through 80 mesh, which is about 177 µm. That is a fine powder: it disperses well in a blend but can dust, cake and cling to surfaces. Granulation improves flow and reduces dust, but it changes the particle-size distribution and the dispersion behaviour in water.

The material is hygroscopic and dispersible in water rather than soluble to a clear solution; in water it forms a phospholipid dispersion. In fats and organic solvents it behaves as a lipid. That dual behaviour is useful in a capsule fill or an oil-based blend and awkward in a dry mix that will see humidity.

Particle size is a finishing specification. A change of mill or sieve can move the 80 mesh result without any change in the PS chemistry, so the particle line should be read with the bulk behaviour, not as a purity number.

Dose arithmetic and the label

The label declares PS, not powder. A formula that declares 100 mg of PS per serving needs 200 mg of a 50% powder, 143 mg of a 70% concentrate, or 500 mg of a 20% dilution. Those are manufacturing figures, not a suggested intake. The arithmetic is the reason a grade switch moves the capsule size and the excipient load even when the declared PS stays the same.

The phospholipid figure does not go on the label as PS. If the powder is 50% PS and 70% phospholipids, the remaining 20 points are other phospholipids, and a label that declares 70% phospholipids as if it were PS overstates the ingredient. Declare the PS figure from the certificate, state the source, and keep the phospholipid figure in the specification.

Overages are a formulation decision. If a capsule is built with an overage, the extra powder changes the fill weight and the label arithmetic; it does not change the grade. Record the basis — as-is — so that the weigh-up and the label use the same number.

What to write into the specification

  • “Phosphatidylserine (sunflower lecithin), PS ≥50.0% by HPLC; total phospholipids ≥70.0%.”
  • “Identification by HPLC phospholipid profile; report the profile.”
  • “Loss on drying ≤5.0%; peroxide value and acid value reported on request.”
  • “Particle size ≥95% through 80 mesh; a granulated form is a separate specification.”
  • “Source: sunflower lecithin; soy statement and fatty acid profile on file.”
  • “Heavy metals and microbiology as listed; pack and storage condition named.”

Write the grade, the source and the particle form as three separate lines. “Sunflower PS 50%” leaves the phospholipid figure, the mesh and the granulated option open, and those are the three lines that decide whether the next lot behaves like the trial lot. The product page carries the catalog figures; the COA page shows how the two assay figures are reported; the stability page covers the pack; the MOQ page covers pack and lead time; the soy page gives the other feedstock's specification; the methods library describes the assay; the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation