06 Identity & adulteration

How we prove an MCT lot is the declared C8/C10 cut

Technical document 06 · Reviewed 2026-11-20 · MCT Oil

On this page
  1. Four questions that prove the oil
  2. The C8/C10 ratio and the full scan
  3. Why X-ray diffraction is not the identity test here
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

An MCT lot is the declared material when the GC fatty-acid profile lands inside the C8 and C10 ranges, the full scan shows the balance a fractionated lauric oil should have, and the free fatty acid, peroxide value and moisture show the oil has not been hydrolysed or oxidised. The profile is the centre of the case, but it does not separate a re-esterified MCT from a physical blend or a diluted oil on its own. The triglyceride distribution and the source complete it.

In one line

Identity is the C8/C10 profile, the full fatty-acid scan and the oxidation state read together; a single MCT figure proves none of them.

Four questions that prove the oil

Naming the material on a certificate is the easy part; proving it is the work. Each layer below answers a different question and stands on its own test, so an answer to the first alone describes a document rather than a drum of oil.

Four layers of MCT oil identity
LayerTest or documentWhat it proves
DocumentName, CAS 73398-61-5, source statementA medium-chain triglyceride of the declared source
Fatty-acid profileGC of the methyl esters, C8 and C10 plus the full scanThe cut, and the absence of a lauric-oil dilution
Triglyceride distributionGC or HPLC by carbon numberA re-esterified oil, not a blend of two triglycerides
ConditionFree fatty acid, peroxide value, moisture, appearanceNot hydrolysed and not oxidised

The order matters. A profile without a condition describes a fresh oil that may not be in the drum; a condition without a profile describes a well-kept oil of unknown identity. The same logic applies to the powder, where the oil load and the carrier sit on top of the profile; that case is on the MCT powder identity page.

The C8/C10 ratio and the full scan

The catalog ranges are C8 55.0–65.0% and C10 35.0–45.0% of the fatty acids. At the edges the ratio runs from about 1.2:1 to about 1.9:1; the midpoint is 60:40. Both edges are inside the specification, so the ratio is a window rather than a single number, and a buyer who needs a tighter window writes it as a separate line.

The rest of the scan is the evidence. A fractionated lauric oil carries small amounts of C6, C12, C14, C16 and C18, and the exact balance depends on the cut. Coconut oil is roughly half lauric acid, so a C12 figure above the agreed limit is the marker of a coconut-oil addition. A C16 or C18 figure that climbs points to a different vegetable oil. Neither is visible on a certificate that reports only C8 and C10.

An oil with added pure C8 sits at the top of the C8 range and the bottom of the C10 range. It can be a legitimate product with its own specification, but it is not the catalog cut, and the certificate should state the cut rather than only the final percentage.

Why X-ray diffraction is not the identity test here

X-ray diffraction identifies crystalline phases, and MCT oil is a liquid at room temperature. A liquid has no long-range lattice to diffract, so a pattern on the oil as supplied says nothing about its identity. Cooling the sample crystallises the triglycerides into polymorphs, and the pattern then depends on the cooling rate and on the polymorph rather than on the C8/C10 cut.

XRD has two uses around this product, and neither is oil identity. It can detect a crystalline mineral filler or a solid adulterant in a suspect sample, and it can check the crystallinity of a starch carrier in the powder. For the oil, the identity tests are GC and the carbon-number distribution; for a solid form, ask what the pattern is being used to prove.

What adulteration looks like

Adulteration patterns in MCT oil and the test that exposes them
PatternWhat it looks likeTest or check
Coconut or palm kernel oilC12 and C14 up; C8 and C10 dilutedFull GC scan; lauric-acid line
Another vegetable oilC16 and C18 up; profile outside the cutFull GC scan; sterol or triglyceride pattern
Added C8Ratio pushed to the top of the rangeC8 and C10 separately; ratio; carbon-number distribution
Older oilClean profile with a high peroxide value or free fatty acidPV, FFA, date of analysis, sensory check
Water or an emulsionCloudy oil; moisture highKarl Fischer; appearance after warming

Colour is the weakest signal. A darker oil can be older, differently bleached or oxidised, and a blend can be adjusted to match the expected shade. The stronger signals are the full scan, the ratio, the free fatty acid and the peroxide value. A certificate that reports appearance and a single C8 figure has not tested the substitution most likely to occur.

How to write identity into the specification

The specification should define the cut, the source and the condition in lines that can be tested together.

  • “Medium-chain triglycerides, CAS 73398-61-5, source declared.”
  • “Caprylic acid 55.0–65.0% and capric acid 35.0–45.0% of total fatty acids by GC; report the full scan.”
  • “Triglyceride carbon-number distribution reported, where the cut has to be distinguished from a blend.”
  • “Free fatty acid ≤0.10%, with the reference acid named.”
  • “Peroxide value ≤1.0 meq O₂/kg; moisture ≤0.1%.”
  • “Lauric acid limit agreed as a separate line where a coconut-oil dilution must be excluded.”

The lines work as a set. If the source changes, the full scan and the allergen file move with it. If the cut changes, the ratio, the dose arithmetic and the label move. A specification that controls only the C8 and C10 ranges leaves the dilution and the condition open.

Five questions for the supplier

  1. What are the C8 and C10 results on this lot, and can you send the full chromatogram rather than the two headline figures?
  2. Which fractionation cut and which source oil were used, and has either changed since the last lot?
  3. What is the free fatty acid result, and which reference acid was used for the calculation?
  4. What are the peroxide value, the moisture and the date of analysis, and how has the lot been stored since?
  5. If a result is challenged, would you join a re-test of the retained sample using the agreed method?

Those five answers, taken together, are an identity file; one C8 figure on its own is not. The catalog specification sits on the MCT oil product page; the carrier form is on the MCT powder page; the certificate lines are explained on the COA page; the chromatographic methods are described in the methods section; the quality page sets out how a lot is released.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation