01 COA & batch testing

What the COA for MCT oil actually contains

Technical document 01 · Reviewed 2026-11-20 · MCT Oil

On this page
  1. The certificate as a test report
  2. What each number is measured against
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. A side-by-side comparison

The certificate for an MCT oil lot reports the GC fatty-acid profile, with caprylic acid (C8:0) at 55.0–65.0% and capric acid (C10:0) at 35.0–45.0%, free fatty acid at ≤0.10%, peroxide value at ≤1.0 meq O₂/kg and moisture at ≤0.1%, beside the heavy-metal panel and microbiology. Each line needs a method, a release limit and a separate column for what the laboratory measured. The limits below are the catalog specification; only the lot certificate speaks for the oil in a particular bottle or drum.

In one line

An MCT certificate is a fatty-acid profile plus a condition: C8 and C10 say what the oil is, while free fatty acid, peroxide value and moisture say how it has been kept.

The certificate as a test report

An oil certificate is short, and easy to read too quickly. The appearance line is a handling check, not an identity test; the identity line is the profile, not a single C8 number. The quality lines are free fatty acid, peroxide value and moisture; everything else is contaminant or hygiene data.

Identity, quality and contaminant tests · MCT oil
ParameterMethodRelease limit
IdentificationGC fatty-acid profileProfile conforms to the reference
Caprylic acid (C8:0)GC of the methyl esters55.0–65.0% of fatty acids
Capric acid (C10:0)GC of the methyl esters35.0–45.0% of fatty acids
Free fatty acidTitration, reference acid named≤0.10%
Peroxide valueIodometric titration≤1.0 meq O₂/kg
MoistureKarl Fischer≤0.1%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyEnumeration and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent

What each number is measured against

The fatty-acid profile is reported as a proportion of the fatty acids, usually by area normalisation of the methyl esters. C8 at 60% means that 60% of the fatty-acid chains are caprylic; it does not mean the oil contains 60% free caprylic acid. Almost all of the acid is esterified to glycerol, so the free fatty acid figure is a separate, much smaller test.

The two ranges do not have to sum to 100%. 65% and 45% together make 110%, so a lot near the top of both ranges has almost no balance left for other chains. The lot still sums to 100% of its fatty acids, with the shortfall met by C6, C12, C14 and C18. A certificate should show the full scan so the balance is visible.

Free fatty acid needs its reference acid. Titration reports acidity as a named fatty acid, and MCT contracts use more than one. The same acidity reads about half as high when expressed as caprylic acid rather than oleic, because the calculation carries the molecular weight of the reference acid: 144.21 against 282.46. A limit of 0.10% as caprylic therefore allows about twice the acidity of 0.10% as oleic. Write the reference acid beside the limit.

Peroxide value is iodometric and reported as milliequivalents of active oxygen per kilogram. It measures primary oxidation products, not the secondary aldehydes a sensory panel detects. Moisture is Karl Fischer and is the gate for hydrolysis: water plus heat splits the triglyceride and raises the free fatty acid.

Release limit versus batch result

One column holds the gate the lot had to meet; the next holds what the laboratory found. A column that simply repeats the gate tells the reader nothing about the lot.

The result side of the certificate
ParameterRelease limitResult column
Caprylic acid55.0–65.0%A measured percentage with the GC method
Capric acid35.0–45.0%A measured percentage from the same run
Free fatty acid≤0.10%A measured percentage, with the reference acid
Peroxide value≤1.0 meq O₂/kgA measured value in meq O₂/kg
Moisture≤0.1%A measured percentage by Karl Fischer

Two results deserve a second look even when they pass. A peroxide value of 0.8 meq O₂/kg is inside the 1.0 limit and leaves little headroom for a slow sea freight; ask the age and the storage history of the lot. A free fatty acid result of 0.09% also passes, and points to a hydrolysis step somewhere in the process.

What moves between batches

Source and cut move the profile. Coconut oil and palm kernel oil are the usual raw materials; the fractionation cut decides how much C8 and C10 is taken, and a different cut moves both figures inside the range. Re-esterification with glycerol then rebuilds the triglyceride, and the completeness of that step shows in the carbon-number distribution.

Free fatty acid moves with moisture and heat: a wet drum, a warm warehouse or a long hold. Peroxide value moves with oxygen, light, trace metals and time; a drum with a large headspace and repeated openings has a different storage history from a sealed one. Moisture moves with the seal and with condensation after a cold journey.

Colour tells the least and often reveals the most. A darker oil can be an older lot, a different bleaching step or an oxidation product while the profile still passes, so read a colour shift as a question, not a rejection. A trend across lots is more useful than one result near an edge: C8 drifting to the boundary, peroxide value climbing, or free fatty acid rising. The lot code should trace from the bottle to the drum to the file sample.

When to order an outside test

An outside laboratory earns its place when qualifying a new supplier, clearing a first consignment into a regulated market, testing a claim the certificate cannot support, or resolving a dispute. The panel: GC fatty-acid profile, triglyceride carbon-number distribution, free fatty acid with its reference acid, peroxide value, moisture and heavy metals by ICP-MS.

For a refined lauric oil, add 3-MCPD and glycidyl esters, and the PAH panel where relevant. Add anisidine value if secondary oxidation is the concern. Ask for the detection limit on every screen; a “not detected” entry without one describes the method, not the oil.

Chain of custody matters as much as the panel: the material tested should be the material retained, and the report should quote the lot code. If a finding is disputed, send the referee laboratory the retained sample, the certificate and the agreed specification, and ask which cause the result supports rather than repeat the same assay.

A side-by-side comparison

Six lines belong in a comparison table: source and cut; the C8 and C10 results plus the full scan; free fatty acid with its reference acid; peroxide value with the date of analysis; moisture; and the pack, its headspace and its lot code. Two quotations that agree on C8 but differ on the reference acid or the age of the lot are not describing the same oil.

The certificate should name who refined and re-esterified the lot, the fractionation cut, the nitrogen status of the drum and what the shelf-life statement covers. The catalog specification sits on the MCT oil product page. The carrier form is specified on the MCT powder page; the analytical methods are described in the methods section; the quality page sets out how a lot is released.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation