MCT 60/40 or a C8-enriched cut: choosing a profile
MCT oil is sold by its C8/C10 cut, not by a single purity figure. The catalog grade is a 60:40 oil with caprylic acid at 55.0–65.0% and capric acid at 35.0–45.0% of the fatty acids; a C8-enriched cut shifts the ratio toward caprylic and changes the viscosity, the cloud point and the mass of each acid that a gram of oil delivers. The oil-versus-powder question is a carrier decision rather than a grade, and it is handled on its own page.
The C8/C10 ratio is the grade: it changes the oil's viscosity, its cloud point and the mass of each fatty acid that a declared dose delivers.
Why an MCT is a cut, not a molecule
Medium-chain triglycerides are a family, not a single substance. The commercial oil is made by hydrolysing a lauric oil, fractionating the fatty acids to take the C8 and C10 fraction, and re-esterifying that fraction with glycerol. The cut is the real specification: how tightly the fractionation holds to C8 and C10, and how much C6, C12 or C14 is allowed to pass through with them.
Coconut oil and palm kernel oil are the usual sources. Neither fixes the ratio by itself, because the fractionation decides it, and the same source can yield a 60:40 oil or a C8-dominant one. That is why a purchase order that names “MCT oil” without ranges has named a category, not a material.
Chain length then drives the physical behaviour. Caprylic acid has eight carbons and capric has ten, and the shorter chain gives a less viscous triglyceride that stays fluid at a lower temperature. A C8-rich cut pours more freely and resists clouding; a C10-rich cut is thicker and clouds sooner. Neither is purer than the other, and neither is automatically the better choice.
The cuts side by side
| Line | Catalog 60:40 | C8-enriched, about 70:30 | C8-dominant, ≥90% C8 |
|---|---|---|---|
| Caprylic acid (C8:0) | 55.0–65.0% | About 70% | ≥90% |
| Capric acid (C10:0) | 35.0–45.0% | About 30% | ≤10% |
| C8:C10 ratio | 1.2–1.9 : 1 | About 2.3 : 1 | 9 : 1 or higher |
| C8 per gram of oil | 550–650 mg | About 700 mg | ≥900 mg |
| C10 per gram of oil | 350–450 mg | About 300 mg | ≤100 mg |
| Viscosity at 20 °C | About 25–33 mPa·s | Lower | Lowest of the three |
| Cold behaviour | Clouds in a cold store | More cold-tolerant | Stays clear longest |
| Typical use | General softgel and blend work | Thinner oil, higher C8 per gram | Maximum C8 per gram |
The enriched columns are indicative profiles quoted against their own specification. The grade supplied here is the 60:40 oil; the other cuts are made on request and carry their own COA.
Viscosity, density and cold behaviour
Viscosity is the property formulators notice first. The catalog oil runs at roughly 25–33 mPa·s at 20 °C, thinner than most seed oils, which is why it fills a softgel easily and disperses into an emulsion with less energy. Density is about 0.93–0.96 g/mL at 20 °C, so a 1 g fill is a little over 1 mL.
MCT oil is insoluble in water and miscible with most fats and oils; it is soluble in ethanol and in the usual organic solvents. In water it does not dissolve, it disperses as droplets once emulsified. That distinction decides the format: a clear drink needs an emulsion or a powder, and an oil layer on the surface is not a solution.
Cold behaviour is physical and reversible. A cold warehouse or a winter journey can cloud the oil or set a fraction; warming it to about 20 °C and mixing restores a clear oil, and the change is not a quality failure. The pack should not be opened while cold, because condensation on the oil is water, and water is the hydrolysis route to free fatty acid.
Mouthfeel follows the chain length too. The shorter chains give a lighter, less coating sensation than a long-chain oil, which is why the 60:40 oil is used in beverages and fillings where a heavy fat layer is unwanted.
The ratio as label arithmetic
The profile is also the label arithmetic. At the floor of the catalog range, 1 g of oil delivers 550 mg of C8 and 350 mg of C10, a total of 900 mg of the two declared acids. At the top of the range it delivers 650 mg and 450 mg. A label that declares 5 g of MCT oil therefore declares between 2.75 g and 3.25 g of C8 and between 1.75 g and 2.25 g of C10.
When the label declares an individual acid rather than the oil, the calculation runs the other way: divide the declared mass by the release floor, not by the midpoint. A 3 g C8 declaration needs at least 3 ÷ 0.55 = 5.45 g of oil at the floor; at the top of the range the same declaration needs 4.62 g. Using the floor keeps the label true across lots.
A softgel fill is set by volume and density. A 1 g fill is about 1.06 mL at 0.94 g/mL; a capsule that holds 0.9 mL holds about 0.85 g of oil. Check the fill against the density of the lot rather than a generic figure, and remember that these are composition figures, not an intake recommendation.
What to write into the specification
The cut has to be written as testable lines. A line that says “MCT oil” without a ratio and without the full scan leaves the dilution question open.
- “Medium-chain triglycerides, CAS 73398-61-5, source declared.”
- “Caprylic acid 55.0–65.0% and capric acid 35.0–45.0% of total fatty acids by GC; report the full scan.”
- “Free fatty acid ≤0.10%, with the reference acid named.”
- “Peroxide value ≤1.0 meq O₂/kg; moisture ≤0.1%.”
- “Lauric acid limit, where a coconut-oil dilution has to be excluded, agreed as a separate line.”
- “Source, fractionation cut and nitrogen status of the pack.”
The last line is not decoration. A C8-enriched oil made by adding pure C8 is a different specification rather than an adulteration, but it is not the catalog cut, and the certificate should say what was done instead of only the final percentage.
When a different cut is the wrong choice
If the formula was built on the 60:40 oil, a C8-dominant cut is not a drop-in. It is thinner, it delivers more C8 per gram, and it moves the fill weight and the label arithmetic. If the label names a ratio, check that the specification delivers the ratio as a range and not only as two separate acid ranges that can both drift.
If the product is a powder, the C8/C10 question stays with the oil inside the powder, but the carrier and the oil load decide the dose. That comparison is on the MCT oil vs MCT powder page. The catalog limits sit on the MCT oil product page; the powder is specified on its own page; the GC method is described in the methods section; the release file is on the quality page.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation