06 Identity & adulteration

How we prove an EPA lot is EPA

Technical document 06 · Reviewed 2026-11-19 · EPA Powder

On this page
  1. Four layers of identity
  2. The EPA/DHA ratio is a fingerprint
  3. Why X-ray diffraction does not identify an oil
  4. What substitution and dilution look like
  5. How to write the identity into the specification
  6. Five questions for a supplier

An EPA lot is identified by a chain of evidence, not by one assay. The chain starts with the declared source and specification, runs through a GC fatty-acid profile with a named standard and internal standard, checks the EPA/DHA ratio and the other fatty acids against the declared oil, and ends with the carrier and oxidation figures on the powder. A lot can pass 10% and still be diluted, substituted or oxidised.

In one line

A 10% assay is a number, not an identity; the profile, the ratio and the matrix have to agree before the lot is EPA powder.

Four layers of identity

The layers are independent; a pass at one does not cover the next. A certificate can be genuine and the powder still not be the declared grade.

The four identity layers for a microencapsulated EPA powder
LayerQuestionEvidence
DocumentWhat is the lot declared to be?Name, CAS, source, specification version, label
ChromatographyIs EPA present at the declared level?GC-FAME, retention time, internal standard, calibration
ProfileIs the fatty-acid background consistent?EPA/DHA ratio, C16:0, C18:1, C18:2, other peaks
MatrixIs the powder what the label says?Carrier, oil load, moisture, PV, p-AV, microbiology

The document layer names EPA, CAS 10417-94-4, the source and the specification version; it is the easiest to copy and the least informative on its own. The chromatographic layer proves that EPA is there; the profile layer says whether the oil around it is the oil that was declared; the matrix layer says whether the powder carries the oil at the stated load.

The EPA/DHA ratio is a fingerprint

The EPA/DHA ratio is a fingerprint, not a purity metric. A fish oil has a characteristic spread; a high-EPA concentrate has a different one; an algal oil is often DHA-rich. The ratio should be calculated from results on the same basis. Comparing an EPA result as free acid with a DHA result as ethyl ester is meaningless, and a certificate that does not state the basis cannot support a ratio.

Other fatty acids carry information: C16:0, C18:0, C18:1, C18:2 and C20:1. A profile with a large C18:2 peak and little EPA or DHA is not a marine oil. A profile that matches the declared oil is consistency, not proof; a blend can be adjusted to hit a ratio. The certificate should report the full FAME profile, at least the major peaks, with the internal standard and the integration.

Why X-ray diffraction does not identify an oil

X-ray diffraction identifies crystalline phases. The oil is liquid or amorphous, and the starch carrier may show a broad pattern that says nothing about the fatty acid. An XRD pattern can tell you about the carrier’s crystalline state; it cannot tell you whether the oil is EPA, DHA or a vegetable oil.

For a mineral powder, XRD can separate a chelate from an oxide. For an oil powder, GC is the identity method. A supplier who offers XRD as the identity test for EPA is answering a different question. FTIR can show that an oil is present, but it does not give the fatty-acid profile; use it as a supporting check, not as the profile.

What substitution and dilution look like

Adulteration cases, what the EPA assay does, and what catches them
CaseWhat the assay doesWhat catches it
Lower-EPA oilPasses at 10% on a higher oil loadOil load, EPA on the oil, carrier mass
Vegetable-oil dilutionPasses only if the EPA is spiked backC18:2 and C18:1 rise; EPA/DHA ratio moves
Oxidised oilEPA can stay above 10%PV, p-AV and TOTOX on the lot
Undeclared sourcePasses; the molecule is the sameSource statement, profile, sterol pattern
Carrier dilutionPasses at 10% with less oilOil load, fill weight, label arithmetic

A 10% powder made from a 20% oil at half the oil load and one made from a 10% oil at full load can both pass. The difference is the carrier and the dose, and neither is visible in the EPA percentage. Adulteration is not always fraud; a change of oil source without a specification change is enough to make the lot different.

How to write the identity into the specification

Write the full identity: “Microencapsulated EPA powder, ≥10.0% EPA by GC, FAME with internal standard, result calculated as free acid, DHA reported, EPA/DHA ratio reported, oil load declared or agreed, carrier modified starch, antioxidant declared, moisture ≤5.0%, PV ≤5.0 meq/kg, p-AV ≤20.0, ≥95% through 40 mesh, heavy metals Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg, microbiology APC ≤1,000 cfu/g with yeast and mould ≤100 cfu/g and E. coli and Salmonella absent, source named, allergen statement attached.”

A specification that says “EPA 10%” and nothing else is a catalog line, not an identity. Source is part of identity for labelling, even though the molecule is the same. The COA should carry the lot code and the specification version, and the pack should carry the same lot code.

Five questions for a supplier

  1. What is the oil source, and what EPA/DHA profile does the oil have before encapsulation?
  2. What is the GC method and basis, and can you send the chromatogram with the lot COA?
  3. What is the oil load, carrier and antioxidant, and are they permitted for our market?
  4. What are the lot PV, p-AV, TOTOX and moisture, and what shelf life is assigned?
  5. Can the lot code on the COA, the pouch and the drum be matched, and is a retained sample held?

A supplier who cannot answer these five leaves the identity unproven. The COA page explains the certificate lines; the grade page explains the difference between an EPA powder and a fish oil powder; the EPA vs DHA page covers the ratio arithmetic. The catalog specification is on the EPA powder product page, and the certificate terms are in the COA glossary entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation