06 Identity & adulteration

How we prove a taurine lot is taurine

Technical document 06 · Reviewed 2026-11-18 · Taurine

On this page
  1. The four layers
  2. The mass balance is the first check to run
  3. Spectroscopy, chromatography and crystallography
  4. The adulteration routes
  5. What to write into the specification
  6. Five questions to put to a supplier

An infrared spectrum and an assay are the two lines most certificates offer as proof of identity, and on their own they are not enough. IR proves that the sample matches a reference spectrum; the assay proves how much acid or how much of the peak is present. Neither one proves that the white crystal in the drum is taurine and not a blend of taurine with glycine, sulfate or another amino acid.

In one line

Identity is a whole-spectrum match plus an impurity fingerprint; an assay on its own cannot separate the molecule from what was added around it.

The four layers

Identity is built in layers, and each layer answers a different question. The first is documentary: the name, the CAS number, the formula and the appearance on the certificate. The second is spectroscopic: an infrared spectrum compared with a reference. The third is quantitative: an assay by a method that can see the molecule. The fourth is the impurity fingerprint: the ash, the anions and the metals that describe what else is in the drum.

Identity layers · what each one proves
LayerTestProvesMisses
DocumentName, CAS, formula, appearanceWhat the lot is calledNothing about the drum
SpectrumIR against a referenceThe functional groups and the solid-state form of the sampleA small adulterant with overlapping bands
AssayHPLC or titration, dried basisHow much taurine the lot containsWhat the remainder is
FingerprintAsh, chloride, sulfate, iron, metalsThe inorganic load and its trendAn organic diluent such as glycine

No single layer is a verdict. The documentary layer is where most disputes start, because a certificate that says “taurine” and a drum that contains taurine plus something else are both described by the same word.

The mass balance is the first check to run

Taurine is a sulfonic acid, not a carboxyl amino acid: it has an amino group and a sulfonic acid group, and it does not form a peptide bond in the usual sense. That matters for identity because the usual amino-acid tests are built around the carboxyl group. A ninhydrin spray will react with the amine, but it will also react with glycine; a titration that counts acid equivalents will count any acid in the sample.

The mass balance is the check that needs no extra test. The assay is reported on the dried basis, and loss on drying, residue on ignition, chloride, sulfate and iron are reported on the same material. Those figures share a denominator, so they have to add up to something close to 100%. An assay near the top of the range with a chloride figure that leaves no room for the stated purity is arithmetically impossible unless one of the numbers is wrong or something else is unaccounted for.

This is not a purity proof, but it is a consistency proof. It catches the certificate that copied a limit instead of reporting a result, the lot whose anions were measured on a different sample, and the blend whose components were assayed separately and added together. Run the sum before you read the assay.

Spectroscopy, chromatography and crystallography

IR is the identity anchor because it is a whole-spectrum comparison. Taurine shows strong sulfonate absorption that a carboxyl amino acid such as glycine does not, and the fingerprint region is sensitive to the crystal form. The limit is sensitivity: a few percent of a well-matched adulterant can hide inside the bands, and a sample pressed as a poor disc can shift the baseline enough to fail a legitimate lot.

HPLC is the selective quantitative method, but taurine has no aromatic chromophore. A method must derivatise the amine or use a detector that does not depend on UV absorbance, and the certificate should name the choice. A titration is cheaper and reproducible, but it measures acid equivalents and is blind to a second acidic species. The two methods are both allowed by the specification; they are not interchangeable as identity evidence.

X-ray diffraction adds the crystal dimension. It confirms that the sample is crystalline and can detect a crystalline inorganic filler such as sodium chloride or sodium sulfate, which IR may not resolve. It is not an assay, and its detection limit should be stated on the report; a “no crystalline impurity detected” line without a limit is not a result.

The adulteration routes

Adulteration routes · taurine
AdulterantWhy it appearsWhat catches it
GlycineInexpensive amino acid, white crystal, similar solubilityIR fingerprint; HPLC profile; the mass balance
Sulfate saltsLow-cost white salt that adds weightSulfate limit and residue on ignition
Chloride saltsLow-cost white salt, freely solubleChloride limit and residue on ignition
Other amino acidsCarry-over from an incomplete purificationHPLC profile and IR comparison
Sugar or starchBulking agent that passes appearanceIR; assay; optical rotation

The inorganic routes are the easy ones to catch, because the ash limit caps how much salt can be added before residue on ignition fails. The organic routes are harder. A blend that carries a small percentage of glycine can pass the assay window and the ash limit together, which is why the IR spectrum and the chromatographic profile carry the weight that the assay cannot.

What to write into the specification

  • “Taurine, 2-aminoethanesulfonic acid, CAS 107-35-7, white crystalline powder.”
  • “Identification: IR conforms to the reference spectrum, with the reference named.”
  • “Assay 98.5–101.5% on the dried basis by HPLC or titration; the method named on the COA.”
  • “Loss on drying ≤0.3%; residue on ignition ≤0.1%; chloride ≤0.05%; sulfate ≤0.03%; iron ≤30 ppm.”
  • “Heavy metals Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg.”
  • “Particle size 20–200 mesh; microbiological limits as specified.”

Five questions to put to a supplier

  1. Which reference spectrum was the IR compared with, and is the spectrum on file for this lot?
  2. Which assay method was used, and what is the result on the as-is basis beside the dried basis?
  3. What are the chloride, sulfate and residue-on-ignition figures for this lot, not just the limits?
  4. Has the lot been screened for glycine or another amino acid, and by which method?
  5. If the material is a blend or a dilution, what was added and at what percentage?

A supplier who can answer these questions is describing a material; a supplier who repeats the specification is describing a catalog. The tests themselves are on the COA page, the grade and route context is on the grade page, and the spectroscopy methods are described in the FTIR and HPLC references. The product page carries the specification.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation