02 Grade comparison

One assay, three questions: choosing a taurine grade

Technical document 02 · Reviewed 2026-11-18 · Taurine

On this page
  1. Why the grade is not the assay
  2. The grades side by side
  3. What changes in the drum
  4. What changes in the finished product
  5. What to write into the specification
  6. When a grade change is not needed

Taurine is one molecule with one catalog assay range, so a grade is not a different purity: it is a different answer to three questions. Which route made it, how finely was it milled, and how much inorganic carry-over does the drum contain? Those three answers decide what the material does in a capsule, a stick pack or a solution, and they are not visible in a “99%” quotation.

In one line

The grade question is not the assay: it is the source route, the particle size and the ash the drum actually carries.

Why the grade is not the assay

Every taurine lot that meets this specification sits inside the same 98.5–101.5% window on the dried basis. Two drums can both be inside it and still differ in ways a formulator feels: one may flow, one may cake; one may dissolve clear, one may leave a haze; one may carry a documented fermentation route, one may not.

The assay is a single number produced by a method that either titrates acid equivalents or separates the molecule chromatographically. It is a good release test and a poor description. The grade is the description: the route behind the crystal, the mesh in front of it, and the ash beside it.

The grades side by side

Taurine grades · what changes in the drum
GradeWhat it isFitsWatch
Fermentation-derivedCrystalline taurine from microbial conversion; standard meshBrands whose label or specification names the routeRoute has to be documented; the COA often does not carry it
SyntheticCrystalline taurine from petrochemical intermediates; standard meshGeneral capsule, tablet and stick useSame specification; route usually absent from the certificate
Low-ashResidue on ignition and anions held well inside the limitsSensitive blends, clear solutions, beveragesMore purification; ask for the actual figures, not the word
Standard ashInside the catalog limits, nearer the capsDry blends where ash does not matterWatch the trend across lots, not one certificate
20–200 mesh powderThe standard crystalline powderCapsules, tablets, dry blendsDust and segregation in a low-dose blend
80 mesh milledFiner powder, milled on requestSticks, suspensions, fast dissolutionFlow drops and caking risk rises
GranulatedAgglomerated on requestTablets, sachets, blends that must runConfirm the granulation aids; it is not a purity change

Reading down the first column is the useful exercise. “Taurine 99%” specifies almost nothing; “taurine, fermentation-derived, low-ash, 80 mesh” specifies a material. The grade name only becomes meaningful when it is tied to a certificate that reports the same parameters.

What changes in the drum

Milling changes particle size, surface area and flow. A fine powder dissolves faster and blends more evenly at a low dose, but it also generates dust, holds static and can segregate in a blend that is moved more than once. A coarse crystal flows well and resists caking, but it may not dissolve fast enough for a stick pack that is stirred into water.

Ash changes the inorganic load. Residue on ignition is the sum of what the purification left behind, and chloride and sulfate are the two anions that usually make it up. A high-ash lot is not a different molecule, but the salts it carries are hygroscopic, so the drum picks up moisture faster and cakes harder under stack pressure. In a clear solution, that same load can show as a faint haze.

Granulation changes flow and dust without changing the chemistry. It is a legitimate way to make a cohesive powder run on a press or fill a sachet, provided the specification names the aids used. A granulated grade is not a purer grade, and it should not be sold as one.

What changes in the finished product

In capsules, the constraint is fill weight and blend uniformity. A typical taurine dose occupies a meaningful share of a capsule, so the powder's bulk density decides how many capsules a formula needs. A finer mesh helps uniformity; a denser granule helps fill weight. Neither changes the assay the label declares.

In tablets, flow and compaction matter more than mesh. A fine milled powder may need granulation to run; a granulated grade may need a different lubricant or a different compression force. In sticks and drink mixes, dissolution and taste move to the front: taurine is an acidic solid, and its 5% solution sits at pH 4.0–6.0, which is a taste and compatibility fact before it is a quality fact.

In gummies and chews, the matrix is the risk. An acidic ingredient plus a reducing sugar plus heat is the condition that browns a batch, and the grade cannot fix a formula that sets those three together. In beverages, clarity and ash are the grade questions; the route is a label question. None of these decisions is settled by the certificate alone.

What to write into the specification

  • “Taurine, 2-aminoethanesulfonic acid, CAS 107-35-7.”
  • “Assay 98.5–101.5% on the dried basis by HPLC or titration; method named on the COA.”
  • “Loss on drying ≤0.3%; residue on ignition ≤0.1%; chloride ≤0.05%; sulfate ≤0.03%.”
  • “Iron ≤30 ppm; heavy metals Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg.”
  • “Particle size 20–200 mesh; source route stated if the label names it.”

A specification that names the route, the mesh and the ash gives the laboratory something to release against. A specification that names only the assay gives the supplier room to change all three without breaching the order.

When a grade change is not needed

If the label does not name the route, the destination market does not require it, and the certificate already supports the claims that are made, choosing a documented fermentation grade buys documentation rather than a better material. If the blend is dry, the ash is comfortably inside the limits, and the finished product is a capsule or a tablet, a low-ash grade solves a problem the formula does not have.

A finer mesh is not an upgrade for a tablet blend that needs density, and a granulated grade is not an upgrade for a capsule formula that already flows. The grade should answer a constraint in the dosage form, the label or the market. When it answers none of them, it is a line on the quotation, not a quality decision.

The tests behind these grades are on the COA page. The route question is expanded on fermentation versus synthetic, the blend risks are on the stability page, and the specification itself is on the taurine product page. Particle size terms are defined in the glossary.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation