01 COA & batch testing

What the COA for L-phenylalanine actually contains

Technical document 01 · Reviewed 2026-11-19 · L-Phenylalanine

On this page
  1. The certificate as a test report
  2. Dried basis, moisture and the rotation basis
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

A certificate for an L-phenylalanine lot reports appearance, identification by infrared and HPLC retention, assay by HPLC on the dried basis, specific rotation, loss on drying, pH, the heavy-metal panel, microbiology and particle size. Each row should carry its method and its release limit, and the measured result belongs in its own column. The limits here are the catalog specification; the batch COA confirms a particular pack.

In one line

The assay states how much phenylalanine is present, the rotation states which enantiomer it is, and a certificate with only the first line has not identified the material.

The certificate as a test report

A certificate is auditable when every row answers three questions: what was measured, with which method, and against which limit. A row that says only “conforms” asks the reader to accept a conclusion without the evidence behind it.

Two rows decide what the powder is. Infrared absorption and HPLC retention say the molecule is phenylalanine; specific rotation says which enantiomer. Neither replaces the other, and the assay replaces neither: a racemate and an L lot can both read 99%.

Identity, assay, moisture and contaminants · L-phenylalanine
ParameterMethodRelease limit
AppearanceVisualWhite crystalline powder
IdentificationIR; HPLC retentionConforms to the reference
Assay (dried basis)HPLC, ultraviolet detection98.5–101.5%
Specific rotationPolarimetry at 589 nm, dried basis-33.0° to -35.5°
Loss on dryingGravimetric≤0.5%
pH (1% solution)Potentiometric5.0–7.0
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 40 mesh

Dried basis, moisture and the rotation basis

The assay is reported on the dried basis. The laboratory measures the powder as received and divides by the dry matter, so the loss on drying has to appear beside the result. A lot at 98.4% as received with 0.35% loss on drying calculates to 98.75% dried; a lot at 98.3% with 0.5% moisture calculates to 98.79% and passes, while 98.3% calculated on the dried basis does not. The correction is small, but it decides release near the floor.

The rotation needs the same discipline. It is calculated on the dried basis, the basis belongs in the rotation row rather than in a footnote, and the row should name the solvent, concentration, temperature and wavelength. Specific rotation depends on all four, so a figure without them cannot be repeated elsewhere or settle a dispute.

Release limit versus batch result

The release limit is the acceptance boundary for a lot; the result is what the laboratory measured. Both belong on the certificate, in separate columns, with the method beside them. A result column filled with the specification range is a copy of the gate, not a measurement.

What the result column should contain
ParameterRelease limitResult column
Assay98.5–101.5% driedA measured percentage with the basis and method
Specific rotation-33.0° to -35.5° driedA measured angle with solvent, concentration and temperature
Loss on drying≤0.5%A measured percentage
Heavy metalsPer elementA measured figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot
Particle size≥95% through 40 meshThe measured percentage through the sieve

Two rows deserve a number rather than a statement. The rotation is the enantiomer line, and “conforms” there hides the one figure that separates the L form from a racemate. The metals are per element, because a single total hides the element that matters for the destination.

What moves between batches

Most of the movement comes from the route and the finishing. Fermentation, enzymatic resolution of an N-acyl derivative and chemical synthesis followed by a classical resolution reach the same molecule with different impurity profiles and different residual solvents. The route also sets the chiral efficiency, which shows in the rotation before it shows anywhere else.

Particle size and bulk density move with milling and crystallisation; the 40 mesh line is a finishing specification and can change with the mill without a change in chemistry. Colour is a weak signal for this material. Crystal habit is the better observation, because it moves with the crystallisation solvent and shows in the flow of the powder.

When to order an outside test

Order an independent test for a new source, a first shipment into a regulated market, a disputed rotation, or a form claim the supplier's certificate does not prove. The useful panel is IR, HPLC assay with the chromatogram, rotation with its method, loss on drying, ICP-MS for the four elements, and microbiology. Add nitrogen by Kjeldahl as a mass-balance check: the theoretical figure is 8.48%, and a large deviation points to a dilution or a different substance.

If the route is synthetic, add a residual-solvent screen. If the enantiomer is disputed, ask for chiral HPLC rather than a second polarimeter reading: the rotation gives the net, the chiral separation gives the composition. Each screen should state its detection limit, and the sample tested should be the sample retained.

What to compare between suppliers

Put six lines side by side: form and CAS number; assay and basis; rotation with its method and solvent; loss on drying; heavy metals and microbiology; pack size and lot code. Two offers that agree on assay but differ on rotation are not describing the same powder.

The second layer is traceability: who manufactured the lot, which route was used, and which milling and packing steps followed. The catalog specification sits on the L-phenylalanine product page. The tests that separate the enantiomers are on the identity page; the HPLC method is described in the HPLC method note, the spectra in the FTIR note, and the rest in the methods library. The release workflow is on the quality page, and the moisture term is defined in the loss-on-drying entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation